Short answer: the Revel F228Be for better sound quality, the Klipsch RP-6000F II for the lower price. The Revel F228Be ranks #16 of 71 floorstanding speakers at $7000. The Klipsch RP-6000F II ranks #54 at $1500, $5500 cheaper.
What the Revel F228Be offers: CEA2034 spinorama shows an essentially flat on-axis response with very nice directivity. Predicted in-room response is nearly perfect, with a smooth slope down from bass to treble. Horizontal beamwidth of about ±70 degrees is wide and holds up well until narrowing above 8kHz. Vertical directivity offers more degrees of listening-height freedom than a typical bookshelf design, a benefit of this tower’s driver layout. Distortion is extremely low across the full audio range at 86dB SPL/1m and stays comfortable even at 96dB SPL/1m. Near-field measurements of the individual drivers show nice, well-integrated crossover behavior with only low-level resonances. Watch for: Minimum impedance dips to 3.4 ohms with a secondary rise around 2kHz, calling for an amplifier comfortable with a demanding load. Very expensive and very heavy (51 kg each).
What the Klipsch RP-6000F II offers: Highest power handling and clean, well-behaved compression at typical volumes. Precise imaging from the controlled horn directivity. Watch for: Worse baffle-step coloration than the smaller RP-5000F II (3-4dB swing vs 2dB), plus a sibilance issue the 5000F doesn’t have - a real regression in tonal balance despite the higher price. Bass extension is mixed - less deep at -3dB (67Hz) than the 5000F - and needs a subwoofer regardless. Narrow horizontal dispersion (~50-60 degrees).
Buy the Revel F228Be if sound quality matters more than the price. Buy the Klipsch RP-6000F II if the price matters more than sound quality.
If sound quality matters at all to you, skip the Klipsch RP-6000F II. It ranks near the bottom of the 71 floorstanding speakers, so look higher up the list instead.
Specifications Side By Side
| Revel F228Be | Klipsch RP-6000F II | |
|---|---|---|
| Price | $7000 | $1500 |
| Ranked | #16 of 71 in Large Size Floorstanding Speakers | #54 of 71 in Large Size Floorstanding Speakers |
| Bass Extension (-10dB) | 25Hz (measured, Audio Science Review) | 33Hz (measured, Erin’s Audio Corner) |
| Bass Extension (-3dB) | 61Hz (measured, Audio Science Review) | 67Hz (measured, Erin’s Audio Corner) |
| Dimensions | 50.9"H x 13.5"W x 17.6"D (1292.9 x 342.9 x 447 mm) | 39.6" x 9.3" x 17.6" (1006 x 236 x 446 mm) |
| Impedance | 8 ohms | 8 ohms nominal (3.7 ohms minimum, measured, Erin’s Audio Corner) |
| Drivers | Dual 8" (200mm) Deep Ceramic Composite aluminum cones, with cast frames woofers, 5-1/4" (130mm) Deep Ceramic Composite aluminum cone, with cast frame midrange, 1" (25mm) Beryllium dome, with acoustic lens waveguide tweeter | 1" titanium tweeter with Tractrix horn, dual 6.5" cerametallic woofers |
| Sensitivity | 89.3dB (300Hz-3kHz @ 2.83V/1m, measured by Audio Science Review; 90dB manufacturer specified) | 90dB (2.83V/1m, measured by Erin’s Audio Corner) |
| Weight | 112.4 lbs / 51 kg each | 49.4 lbs / 22.4 kg |
| Woofer Cabinet | ported, front | ported, rear |
| Frequency Response | - | 38Hz - 25kHz (+-3dB, Manufacturer specified) |
| Crossover Frequency | - | 1770Hz |
| Output Power | - | 125W continuous, 500W peak |
Related Speaker Comparisons
More useful head-to-heads from the same speaker class:
- MoFi SourcePoint V10 Master Edition vs Polk T50
- Dynaudio Emit 30 vs Revel F226Be
- Polk T50 vs Revel F226Be
- Magnepan LRS+ vs Revel F228Be
- Dynaudio Emit 30 vs Revel F228Be
Prices on this page were last checked August 25, 2026 at 6:19 AM UTC. Product prices and availability are accurate as of that date/time and are subject to change; the price and availability shown on Amazon at the time of purchase will apply to the purchase of this product.
As an eBay Partner, we may be compensated if you make a purchase.
The Two Speakers In Full
Revel F228Be: $7000 Crutchfield eBay
Pros: CEA2034 spinorama shows an essentially flat on-axis response with very nice directivity. Predicted in-room response is nearly perfect, with a smooth slope down from bass to treble. Horizontal beamwidth of about ±70 degrees is wide and holds up well until narrowing above 8kHz. Vertical directivity offers more degrees of listening-height freedom than a typical bookshelf design, a benefit of this tower’s driver layout. Distortion is extremely low across the full audio range at 86dB SPL/1m and stays comfortable even at 96dB SPL/1m. Near-field measurements of the individual drivers show nice, well-integrated crossover behavior with only low-level resonances.
Cons: Minimum impedance dips to 3.4 ohms with a secondary rise around 2kHz, calling for an amplifier comfortable with a demanding load. Very expensive and very heavy (51 kg each).
Full Revel F228Be review and specifications →
| Bass Extension (-10dB) | 25Hz (measured, Audio Science Review) |
|---|---|
| Bass Extension (-3dB) | 61Hz (measured, Audio Science Review) |
| Dimensions | 50.9"H x 13.5"W x 17.6"D (1292.9 x 342.9 x 447 mm) |
| Drivers | Dual 8" (200mm) Deep Ceramic Composite aluminum cones, with cast frames woofers, 5-1/4" (130mm) Deep Ceramic Composite aluminum cone, with cast frame midrange, 1" (25mm) Beryllium dome, with acoustic lens waveguide tweeter |
| Impedance | 8 ohms |
| Sensitivity | 89.3dB (300Hz-3kHz @ 2.83V/1m, measured by Audio Science Review; 90dB manufacturer specified) |
| Weight | 112.4 lbs / 51 kg each |
| Woofer Cabinet | ported, front |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
Klipsch RP-6000F II: $1500 Amazon eBay
Pros: Highest power handling and clean, well-behaved compression at typical volumes. Precise imaging from the controlled horn directivity.
Cons: Worse baffle-step coloration than the smaller RP-5000F II (3-4dB swing vs 2dB), plus a sibilance issue the 5000F doesn’t have - a real regression in tonal balance despite the higher price. Bass extension is mixed - less deep at -3dB (67Hz) than the 5000F - and needs a subwoofer regardless. Narrow horizontal dispersion (~50-60 degrees).
Full Klipsch RP-6000F II review and specifications →
| Bass Extension (-10dB) | 33Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 67Hz (measured, Erin's Audio Corner) |
| Crossover Frequency | 1770Hz |
| Dimensions | 39.6" x 9.3" x 17.6" (1006 x 236 x 446 mm) |
| Drivers | 1" titanium tweeter with Tractrix horn, dual 6.5" cerametallic woofers |
| Frequency Response | 38Hz - 25kHz (+-3dB, Manufacturer specified) |
| Impedance | 8 ohms nominal (3.7 ohms minimum, measured, Erin's Audio Corner) |
| Output Power | 125W continuous, 500W peak |
| Sensitivity | 90dB (2.83V/1m, measured by Erin's Audio Corner) |
| Weight | 49.4 lbs / 22.4 kg |
| Woofer Cabinet | ported, rear |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- Klipsch RP-6000F II vs Dynaudio Emit 30
- Klipsch RP-6000F II vs Polk T50
- Klipsch RP-6000F II vs Klipsch RP-8000F II
- Klipsch RP-6000F II vs Focal Aria Evo X N°2
- Klipsch RP-6000F II vs Sony SS-CS3
- Klipsch RP-6000F II vs SVS Ultra Evolution Pinnacle
- Klipsch RP-6000F II vs Klipsch RP-5000F II
- Klipsch RP-6000F II vs Infinity Reference 253
- See all 35 comparisons