Short answer: the JBL 4367 for better sound quality, the Klipsch RP-5000F II for the lower price. The JBL 4367 ranks #12 of 71 floorstanding speakers at $16500. The Klipsch RP-5000F II ranks #48 at $1199.98, $15300.02 cheaper.
What the Klipsch RP-5000F II offers: The most tonally coherent of the RP II floorstander line, with a mild baffle-step dip and treble tilt but no additional coloration issues beyond that. Precise imaging thanks to the controlled horn/waveguide directivity. Watch for: Bass extension is underwhelming for a floorstander - F3 at 55Hz, F10 at 41Hz - and needs a subwoofer. Narrow horizontal dispersion (~50-60 degrees) trades soundstage width for imaging precision. A mild high-frequency tilt and a slight lack of detail around 1-1.5kHz.
What the JBL 4367 offers: Three-way design pairing a 15” front-ported woofer with a compression driver on a controlled-dispersion horn/waveguide, crossed over at 700Hz. On-axis frequency response is nearly dead flat, holding within about ±1.5dB, with the listening window tracking it closely except right at the crossover. Distortion stays below 1% THD across the entire audible band at both 86dB and 96dB. Compression/dynamic-range linearity is exceptional - within about a quarter of a dB from 76dB to 102dB, among the best the reviewer has measured. High sensitivity (about 92.6dB average) eases the amplifier match despite the speaker’s size. Minimal rear radiation thanks to the 15” woofer’s directivity and front-firing ports - rear energy runs about 20dB down from the primary wavefront, giving it a near-cardioid radiation pattern. Well-controlled horn directivity keeps the soundstage from noticeably shifting in width across the 700Hz crossover region. A natural high-frequency rolloff above about 7-8kHz gives it an easy, non-fatiguing character for extended listening sessions. Watch for: At roughly $16,500/pair, this is a major investment - the reviewer recommends buying from a dealer with a liberal return policy. Vertical response shows dips beyond about ±10-20°, with a larger null further out - an inherent trade-off of mating a 15” woofer to a horn compression driver at a 700Hz crossover, since crossing lower would hurt power handling and dynamic range. Horizontal directivity isn’t perfectly consistent with frequency: narrow (about ±20°) through 200-800Hz, briefly widening to near ±50° above the crossover, then narrowing again at high frequency - an unusual, non-constant pattern. The high-frequency rolloff that gives it an easy-listening character also reduces the sense of air and space in the soundstage when listening from off-center seats. Massive and heavy (about 120 lbs, roughly 36-37” tall) - needs to be raised on a stand to bring the horn to ear level, and isn’t something one person easily moves alone. Only modest EQ adjustment is available on the speaker itself (about ±1-2dB bass/treble trim).
Buy the Klipsch RP-5000F II if the price matters more than sound quality. Buy the JBL 4367 if sound quality matters more than the price.
Specifications Side By Side
| Klipsch RP-5000F II | JBL 4367 | |
|---|---|---|
| Price | $1199.98 | $16500 |
| Ranked | #48 of 71 in Large Size Floorstanding Speakers | #12 of 71 in Large Size Floorstanding Speakers |
| Bass Extension (-10dB) | 41Hz (measured, Erin’s Audio Corner) | 31Hz (measured, Erin’s Audio Corner) |
| Bass Extension (-3dB) | 55Hz (measured, Erin’s Audio Corner) | 43Hz (measured, Erin’s Audio Corner) |
| Sensitivity | 90dB (2.83V/1m, measured by Erin’s Audio Corner) | 92.5dB (measured average, Erin’s Audio Corner) |
| Drivers | 1" titanium tweeter with Tractrix horn, dual 5.25" cerametallic woofers | 15" (380mm) 2216Nd-1 Dual Differential Drive® woofer, 3" (75mm) D2430K dual compression tweeter |
| Weight | 38.6 lbs / 17.5 kg | 119 lbs / 54 kg each |
| Impedance | 8 ohms nominal, 3.3 ohms minimum (measured above 80Hz, Erin’s Audio Corner) | 4 ohms nominal (5.3 ohms minimum above 80Hz, measured by Erin’s Audio Corner) |
| Frequency Response | 40Hz - 25kHz (+-3dB, Manufacturer specified) | - |
| Crossover Frequency | 1900Hz | - |
| Output Power | 100W continuous, 400W peak | - |
| Dimensions | 36.1" x 8.1" x 14.8" (917 x 207 x 375 mm) | 37.2"H x 22.2"W x 16.8"D (944.9 x 563.9 x 426.7 mm) |
| Woofer Cabinet | ported, rear | ported, front |
Related Speaker Comparisons
More useful head-to-heads from the same speaker class:
- Revel F328Be vs KEF Reference 203
- Revel F226Be vs PS Audio Aspen FR10
- Revel F226Be vs MoFi SourcePoint V10 Master Edition
- JBL 4367 vs Polk Audio Reserve R700
- Q Acoustics 5040 vs JBL 4367
Prices on this page were last checked August 25, 2026 at 6:19 AM UTC. Product prices and availability are accurate as of that date/time and are subject to change; the price and availability shown on Amazon at the time of purchase will apply to the purchase of this product.
As an eBay Partner, we may be compensated if you make a purchase.
The Two Speakers In Full
Klipsch RP-5000F II: $1199.98 Amazon eBay
Pros: The most tonally coherent of the RP II floorstander line, with a mild baffle-step dip and treble tilt but no additional coloration issues beyond that. Precise imaging thanks to the controlled horn/waveguide directivity.
Cons: Bass extension is underwhelming for a floorstander - F3 at 55Hz, F10 at 41Hz - and needs a subwoofer. Narrow horizontal dispersion (~50-60 degrees) trades soundstage width for imaging precision. A mild high-frequency tilt and a slight lack of detail around 1-1.5kHz.
Full Klipsch RP-5000F II review and specifications →
| Bass Extension (-10dB) | 41Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 55Hz (measured, Erin's Audio Corner) |
| Crossover Frequency | 1900Hz |
| Dimensions | 36.1" x 8.1" x 14.8" (917 x 207 x 375 mm) |
| Drivers | 1" titanium tweeter with Tractrix horn, dual 5.25" cerametallic woofers |
| Frequency Response | 40Hz - 25kHz (+-3dB, Manufacturer specified) |
| Impedance | 8 ohms nominal, 3.3 ohms minimum (measured above 80Hz, Erin's Audio Corner) |
| Output Power | 100W continuous, 400W peak |
| Sensitivity | 90dB (2.83V/1m, measured by Erin's Audio Corner) |
| Weight | 38.6 lbs / 17.5 kg |
| Woofer Cabinet | ported, rear |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- Klipsch RP-5000F II vs SVS Ultra Evolution Pinnacle
- Klipsch RP-5000F II vs KEF Q11 Meta
- Klipsch RP-5000F II vs Monolith THX-365T
- Klipsch RP-5000F II vs Klipsch RP-8000F II
- Klipsch RP-5000F II vs Klipsch Heresy IV
- Klipsch RP-5000F II vs Dynaudio Emit 30
- Klipsch RP-5000F II vs Polk Audio XT60
- Klipsch RP-5000F II vs Klipsch RP-6000F II
- See all 41 comparisons
JBL 4367: $16500 eBay
Pros: Three-way design pairing a 15” front-ported woofer with a compression driver on a controlled-dispersion horn/waveguide, crossed over at 700Hz. On-axis frequency response is nearly dead flat, holding within about ±1.5dB, with the listening window tracking it closely except right at the crossover. Distortion stays below 1% THD across the entire audible band at both 86dB and 96dB. Compression/dynamic-range linearity is exceptional - within about a quarter of a dB from 76dB to 102dB, among the best the reviewer has measured. High sensitivity (about 92.6dB average) eases the amplifier match despite the speaker’s size. Minimal rear radiation thanks to the 15” woofer’s directivity and front-firing ports - rear energy runs about 20dB down from the primary wavefront, giving it a near-cardioid radiation pattern. Well-controlled horn directivity keeps the soundstage from noticeably shifting in width across the 700Hz crossover region. A natural high-frequency rolloff above about 7-8kHz gives it an easy, non-fatiguing character for extended listening sessions.
Cons: At roughly $16,500/pair, this is a major investment - the reviewer recommends buying from a dealer with a liberal return policy. Vertical response shows dips beyond about ±10-20°, with a larger null further out - an inherent trade-off of mating a 15” woofer to a horn compression driver at a 700Hz crossover, since crossing lower would hurt power handling and dynamic range. Horizontal directivity isn’t perfectly consistent with frequency: narrow (about ±20°) through 200-800Hz, briefly widening to near ±50° above the crossover, then narrowing again at high frequency - an unusual, non-constant pattern. The high-frequency rolloff that gives it an easy-listening character also reduces the sense of air and space in the soundstage when listening from off-center seats. Massive and heavy (about 120 lbs, roughly 36-37” tall) - needs to be raised on a stand to bring the horn to ear level, and isn’t something one person easily moves alone. Only modest EQ adjustment is available on the speaker itself (about ±1-2dB bass/treble trim).
Full JBL 4367 review and specifications →
| Bass Extension (-10dB) | 31Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 43Hz (measured, Erin's Audio Corner) |
| Dimensions | 37.2"H x 22.2"W x 16.8"D (944.9 x 563.9 x 426.7 mm) |
| Drivers | 15" (380mm) 2216Nd-1 Dual Differential Drive® woofer, 3" (75mm) D2430K dual compression tweeter |
| Impedance | 4 ohms nominal (5.3 ohms minimum above 80Hz, measured by Erin's Audio Corner) |
| Sensitivity | 92.5dB (measured average, Erin's Audio Corner) |
| Weight | 119 lbs / 54 kg each |
| Woofer Cabinet | ported, front |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons