Short answer: the Revel F208 for better sound quality, the Polk Audio XT60 for the lower price. The Revel F208 ranks #15 of 71 floorstanding speakers at $2400. The Polk Audio XT60 ranks #43 at $229, $2171 cheaper.
What the Revel F208 offers: CEA2034 spinorama shows a fairly even on-axis response with sensitivity matching spec at ~87-88dB. Predicted in-room response is a smooth, textbook-quality downward slope that should translate well to most rooms without correction. Early reflections sum so cleanly with the direct sound that side-wall absorption isn’t recommended - it would work against the speaker’s naturally well-integrated off-axis behavior. Distortion stays below 0.5% from 100Hz up at 96dB/1m, with all distortion components falling below audible threshold above 200Hz. Very wide horizontal directivity of about ±75 degrees. Measured performance was judged very close to Revel’s own flagship Salon2, and Revel’s speakers (including this one) are developed using Harman’s double-blind listening test methodology. Preference score of 6.6 (7.7 with a subwoofer added). Watch for: Some directivity error and tweeter-response ripple right at the 2.2kHz crossover point. A notable on-axis dip at about 4kHz, attributed to probable cabinet diffraction. Cumulative spectral decay (waterfall) shows an unexplained resonance around 4-5kHz that the reviewer couldn’t pin down a clear cause for. Vertical directivity shows narrowband interference nulls just above and below the tweeter axis (roughly 2-3kHz), typical of a non-coaxial tower with vertically separated drivers, so listening height matters more than it would with a coincident design. Minimum impedance dips to 3.4 ohms, calling for a robust, high-current amplifier. Distortion climbs substantially below about 80-100Hz (up to ~5% in the deep bass) when driven hard, an excursion-limited trade-off typical of towers at high output. Isolating the woofers alone shows their usable range ending around 500-700Hz at the crossover, with somewhat elevated (though still low in absolute terms) 2nd/3rd harmonic distortion in the 100-300Hz region.
What the Polk Audio XT60 offers: Passive-radiator-loaded design (6.5” woofer plus two 6.5” passive radiators) gives deeper bass than the driver size alone would suggest - 43.9Hz at -3dB / 38.1Hz at -10dB, genuinely competitive extension for a budget tower. Hi-Res Audio certified, Dolby Atmos/DTS:X compatible, and works with either 4- or 8-ohm amplifier outputs. Watch for: Bass alignment Q (lfq 0.96) is the highest, least-controlled figure in this entire batch, consistent with owner reports of a slightly loose, boomy low end at higher volumes. On-axis deviation (nbd_on_axis 0.512) is also the roughest measured figure in the batch. The vinyl-wrapped (not wood veneer) cabinet reads as budget up close per owner reviews, and at least one owner reported blowing a driver under sustained heavy bass - some caution is warranted with bass-heavy source material at volume.
Buy the Revel F208 if sound quality matters more than the price. Buy the Polk Audio XT60 if the price matters more than sound quality.
Specifications Side By Side
| Revel F208 | Polk Audio XT60 | |
|---|---|---|
| Price | $2400 used, Discontinued | $229.00 |
| Ranked | #15 of 71 in Large Size Floorstanding Speakers | #43 of 71 in Large Size Floorstanding Speakers |
| Bass Extension (-10dB) | 24Hz (measured, Audio Science Review) | 38.1Hz (measured, spinorama.org) |
| Bass Extension (-3dB) | 47Hz (measured, Audio Science Review) | 43.9Hz (measured, spinorama.org) |
| Dimensions | 46.6"H x 13.5"W x 14.8"D (1183.6 x 342.9 x 375.9 mm) | 19.05 x 92.5 x 23.09cm (7.5 x 36.4 x 9.09 in) each |
| Impedance | 8 ohms nominal, 3.5 ohms minimum (measured, Audio Science Review) | 4/8-ohm compatible |
| Drivers | Dual 8" (20 cm) Aluminum Cone, Cast-frame Woofers, 5.25" (13.3 cm) Aluminum Cone, Cast-frame Midrange, 1" (2.5 cm) Aluminum Tweeter with Acoustic Lens Waveguide | 1" Terylene dome tweeter, 6.5" bilaminate polypropylene woofer, 2x 6.5" passive radiators |
| Sensitivity | 88.2dB (measured by Audio Science Review; 88.5dB manufacturer specified) | 86dB (1W/1m) |
| Weight | 79.4 lbs / 36 kg each | 20 lbs / 9.07 kg (20 lb) each |
| Woofer Cabinet | ported, front | Passive radiator-loaded |
| Discontinued | Yes | - |
Related Speaker Comparisons
More useful head-to-heads from the same speaker class:
- Focal Chora 816 vs Klipsch RP-8000F II
- Focal Chora 816 vs Klipsch RP-6000F II
- Focal Chora 816 vs Revel F206
- Polk Audio XT60 vs Focal Aria Evo X N°2
- Revel F208 vs Polk T50
Prices on this page were last checked August 25, 2026 at 6:19 AM UTC. Product prices and availability are accurate as of that date/time and are subject to change; the price and availability shown on Amazon at the time of purchase will apply to the purchase of this product.
As an eBay Partner, we may be compensated if you make a purchase.
The Two Speakers In Full
Revel F208: $2400 used, Discontinued eBay
Pros: CEA2034 spinorama shows a fairly even on-axis response with sensitivity matching spec at ~87-88dB. Predicted in-room response is a smooth, textbook-quality downward slope that should translate well to most rooms without correction. Early reflections sum so cleanly with the direct sound that side-wall absorption isn’t recommended - it would work against the speaker’s naturally well-integrated off-axis behavior. Distortion stays below 0.5% from 100Hz up at 96dB/1m, with all distortion components falling below audible threshold above 200Hz. Very wide horizontal directivity of about ±75 degrees. Measured performance was judged very close to Revel’s own flagship Salon2, and Revel’s speakers (including this one) are developed using Harman’s double-blind listening test methodology. Preference score of 6.6 (7.7 with a subwoofer added).
Cons: Some directivity error and tweeter-response ripple right at the 2.2kHz crossover point. A notable on-axis dip at about 4kHz, attributed to probable cabinet diffraction. Cumulative spectral decay (waterfall) shows an unexplained resonance around 4-5kHz that the reviewer couldn’t pin down a clear cause for. Vertical directivity shows narrowband interference nulls just above and below the tweeter axis (roughly 2-3kHz), typical of a non-coaxial tower with vertically separated drivers, so listening height matters more than it would with a coincident design. Minimum impedance dips to 3.4 ohms, calling for a robust, high-current amplifier. Distortion climbs substantially below about 80-100Hz (up to ~5% in the deep bass) when driven hard, an excursion-limited trade-off typical of towers at high output. Isolating the woofers alone shows their usable range ending around 500-700Hz at the crossover, with somewhat elevated (though still low in absolute terms) 2nd/3rd harmonic distortion in the 100-300Hz region. Discontinued.
Full Revel F208 review and specifications →
| Bass Extension (-10dB) | 24Hz (measured, Audio Science Review) |
|---|---|
| Bass Extension (-3dB) | 47Hz (measured, Audio Science Review) |
| Dimensions | 46.6"H x 13.5"W x 14.8"D (1183.6 x 342.9 x 375.9 mm) |
| Discontinued | Yes |
| Drivers | Dual 8" (20 cm) Aluminum Cone, Cast-frame Woofers, 5.25" (13.3 cm) Aluminum Cone, Cast-frame Midrange, 1" (2.5 cm) Aluminum Tweeter with Acoustic Lens Waveguide |
| Impedance | 8 ohms nominal, 3.5 ohms minimum (measured, Audio Science Review) |
| Sensitivity | 88.2dB (measured by Audio Science Review; 88.5dB manufacturer specified) |
| Weight | 79.4 lbs / 36 kg each |
| Woofer Cabinet | ported, front |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
Polk Audio XT60: $229.00 Amazon Bhphotovideo Crutchfield eBay
Pros: Passive-radiator-loaded design (6.5” woofer plus two 6.5” passive radiators) gives deeper bass than the driver size alone would suggest - 43.9Hz at -3dB / 38.1Hz at -10dB, genuinely competitive extension for a budget tower. Hi-Res Audio certified, Dolby Atmos/DTS:X compatible, and works with either 4- or 8-ohm amplifier outputs.
Cons: Bass alignment Q (lfq 0.96) is the highest, least-controlled figure in this entire batch, consistent with owner reports of a slightly loose, boomy low end at higher volumes. On-axis deviation (nbd_on_axis 0.512) is also the roughest measured figure in the batch. The vinyl-wrapped (not wood veneer) cabinet reads as budget up close per owner reviews, and at least one owner reported blowing a driver under sustained heavy bass - some caution is warranted with bass-heavy source material at volume.
Full Polk Audio XT60 review and specifications →
| Bass Extension (-10dB) | 38.1Hz (measured, spinorama.org) |
|---|---|
| Bass Extension (-3dB) | 43.9Hz (measured, spinorama.org) |
| Dimensions | 19.05 x 92.5 x 23.09cm (7.5 x 36.4 x 9.09 in) each |
| Drivers | 1" Terylene dome tweeter, 6.5" bilaminate polypropylene woofer, 2x 6.5" passive radiators |
| Impedance | 4/8-ohm compatible |
| Sensitivity | 86dB (1W/1m) |
| Weight | 20 lbs / 9.07 kg (20 lb) each |
| Woofer Cabinet | Passive radiator-loaded |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- Polk Audio XT60 vs Klipsch Heresy IV
- Polk Audio XT60 vs Klipsch Forte IV
- Polk Audio XT60 vs KEF Q11 Meta
- Polk Audio XT60 vs Definitive Technology BP-9020
- Polk Audio XT60 vs Klipsch RP-5000F II
- Polk Audio XT60 vs Polk Reserve R500
- Polk Audio XT60 vs ELAC Debut 3.0 DF63
- Polk Audio XT60 vs PSB Imagine T65
- See all 27 comparisons