Short answer: the Revel F208 for better sound quality, the Klipsch RP-5000F II for the lower price. The Revel F208 ranks #15 of 68 floorstanding speakers at $2400. The Klipsch RP-5000F II ranks #48 at $1199.98, $1200.02 cheaper.
What the Revel F208 offers: CEA2034 spinorama shows a fairly even on-axis response with sensitivity matching spec at ~87-88dB. Predicted in-room response is a smooth, textbook-quality downward slope that should translate well to most rooms without correction. Early reflections sum so cleanly with the direct sound that side-wall absorption isn’t recommended - it would work against the speaker’s naturally well-integrated off-axis behavior. Distortion stays below 0.5% from 100Hz up at 96dB/1m, with all distortion components falling below audible threshold above 200Hz. Very wide horizontal directivity of about ±75 degrees. Measured performance was judged very close to Revel’s own flagship Salon2, and Revel’s speakers (including this one) are developed using Harman’s double-blind listening test methodology. Preference score of 6.6 (7.7 with a subwoofer added). Watch for: Some directivity error and tweeter-response ripple right at the 2.2kHz crossover point. A notable on-axis dip at about 4kHz, attributed to probable cabinet diffraction. Cumulative spectral decay (waterfall) shows an unexplained resonance around 4-5kHz that the reviewer couldn’t pin down a clear cause for. Vertical directivity shows narrowband interference nulls just above and below the tweeter axis (roughly 2-3kHz), typical of a non-coaxial tower with vertically separated drivers, so listening height matters more than it would with a coincident design. Minimum impedance dips to 3.4 ohms, calling for a robust, high-current amplifier. Distortion climbs substantially below about 80-100Hz (up to ~5% in the deep bass) when driven hard, an excursion-limited trade-off typical of towers at high output. Isolating the woofers alone shows their usable range ending around 500-700Hz at the crossover, with somewhat elevated (though still low in absolute terms) 2nd/3rd harmonic distortion in the 100-300Hz region.
What the Klipsch RP-5000F II offers: The most tonally coherent of the RP II floorstander line, with a mild baffle-step dip and treble tilt but no additional coloration issues beyond that. Precise imaging thanks to the controlled horn/waveguide directivity. Watch for: Bass extension is underwhelming for a floorstander - F3 at 55Hz, F10 at 41Hz - and needs a subwoofer. Narrow horizontal dispersion (~50-60 degrees) trades soundstage width for imaging precision. A mild high-frequency tilt and a slight lack of detail around 1-1.5kHz.
Buy the Revel F208 if sound quality matters more than the price. Buy the Klipsch RP-5000F II if the price matters more than sound quality.
Specifications Side By Side
| Revel F208 | Klipsch RP-5000F II | |
|---|---|---|
| Price | $2400 used, Discontinued | $1199.98 |
| Ranked | #15 of 68 in Large Size Floorstanding Speakers | #48 of 68 in Large Size Floorstanding Speakers |
| Bass Extension (-10dB) | 24Hz (measured, Audio Science Review) | 41Hz (measured, Erin’s Audio Corner) |
| Bass Extension (-3dB) | 47Hz (measured, Audio Science Review) | 55Hz (measured, Erin’s Audio Corner) |
| Dimensions | 46.6"H x 13.5"W x 14.8"D (1183.6 x 342.9 x 375.9 mm) | 36.1" x 8.1" x 14.8" (917 x 207 x 375 mm) |
| Impedance | 8 ohms nominal, 3.5 ohms minimum (measured, Audio Science Review) | 8 ohms nominal, 3.3 ohms minimum (measured above 80Hz, Erin’s Audio Corner) |
| Drivers | Dual 8" (20 cm) Aluminum Cone, Cast-frame Woofers, 5.25" (13.3 cm) Aluminum Cone, Cast-frame Midrange, 1" (2.5 cm) Aluminum Tweeter with Acoustic Lens Waveguide | 1" titanium tweeter with Tractrix horn, dual 5.25" cerametallic woofers |
| Sensitivity | 88.2dB (measured by Audio Science Review; 88.5dB manufacturer specified) | 90dB (2.83V/1m, measured by Erin’s Audio Corner) |
| Weight | 79.4 lbs / 36 kg each | 38.6 lbs / 17.5 kg |
| Woofer Cabinet | ported, front | ported, rear |
| Discontinued | Yes | - |
| Frequency Response | - | 40Hz - 25kHz (+-3dB, Manufacturer specified) |
| Crossover Frequency | - | 1900Hz |
| Output Power | - | 100W continuous, 400W peak |
Related Speaker Comparisons
More useful head-to-heads from the same speaker class:
- PSB Imagine T65 vs Focal Chora 816
- KLH Model Five vs Klipsch RP-8000F II
- KEF R5 vs Focal Chora 816
- Revel F208 vs Polk Audio Reserve R700
- Klipsch RP-5000F II vs Focal Aria Evo X N°2
Prices on this page were last checked August 24, 2026 at 6:53 AM UTC. Product prices and availability are accurate as of that date/time and are subject to change; the price and availability shown on Amazon at the time of purchase will apply to the purchase of this product.
As an eBay Partner, we may be compensated if you make a purchase.
The Two Speakers In Full
Revel F208: $2400 used, Discontinued eBay
Pros: CEA2034 spinorama shows a fairly even on-axis response with sensitivity matching spec at ~87-88dB. Predicted in-room response is a smooth, textbook-quality downward slope that should translate well to most rooms without correction. Early reflections sum so cleanly with the direct sound that side-wall absorption isn’t recommended - it would work against the speaker’s naturally well-integrated off-axis behavior. Distortion stays below 0.5% from 100Hz up at 96dB/1m, with all distortion components falling below audible threshold above 200Hz. Very wide horizontal directivity of about ±75 degrees. Measured performance was judged very close to Revel’s own flagship Salon2, and Revel’s speakers (including this one) are developed using Harman’s double-blind listening test methodology. Preference score of 6.6 (7.7 with a subwoofer added).
Cons: Some directivity error and tweeter-response ripple right at the 2.2kHz crossover point. A notable on-axis dip at about 4kHz, attributed to probable cabinet diffraction. Cumulative spectral decay (waterfall) shows an unexplained resonance around 4-5kHz that the reviewer couldn’t pin down a clear cause for. Vertical directivity shows narrowband interference nulls just above and below the tweeter axis (roughly 2-3kHz), typical of a non-coaxial tower with vertically separated drivers, so listening height matters more than it would with a coincident design. Minimum impedance dips to 3.4 ohms, calling for a robust, high-current amplifier. Distortion climbs substantially below about 80-100Hz (up to ~5% in the deep bass) when driven hard, an excursion-limited trade-off typical of towers at high output. Isolating the woofers alone shows their usable range ending around 500-700Hz at the crossover, with somewhat elevated (though still low in absolute terms) 2nd/3rd harmonic distortion in the 100-300Hz region. Discontinued.
Full Revel F208 review and specifications →
| Bass Extension (-10dB) | 24Hz (measured, Audio Science Review) |
|---|---|
| Bass Extension (-3dB) | 47Hz (measured, Audio Science Review) |
| Dimensions | 46.6"H x 13.5"W x 14.8"D (1183.6 x 342.9 x 375.9 mm) |
| Discontinued | Yes |
| Drivers | Dual 8" (20 cm) Aluminum Cone, Cast-frame Woofers, 5.25" (13.3 cm) Aluminum Cone, Cast-frame Midrange, 1" (2.5 cm) Aluminum Tweeter with Acoustic Lens Waveguide |
| Impedance | 8 ohms nominal, 3.5 ohms minimum (measured, Audio Science Review) |
| Sensitivity | 88.2dB (measured by Audio Science Review; 88.5dB manufacturer specified) |
| Weight | 79.4 lbs / 36 kg each |
| Woofer Cabinet | ported, front |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
Klipsch RP-5000F II: $1199.98 Amazon eBay
Pros: The most tonally coherent of the RP II floorstander line, with a mild baffle-step dip and treble tilt but no additional coloration issues beyond that. Precise imaging thanks to the controlled horn/waveguide directivity.
Cons: Bass extension is underwhelming for a floorstander - F3 at 55Hz, F10 at 41Hz - and needs a subwoofer. Narrow horizontal dispersion (~50-60 degrees) trades soundstage width for imaging precision. A mild high-frequency tilt and a slight lack of detail around 1-1.5kHz.
Full Klipsch RP-5000F II review and specifications →
| Bass Extension (-10dB) | 41Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 55Hz (measured, Erin's Audio Corner) |
| Crossover Frequency | 1900Hz |
| Dimensions | 36.1" x 8.1" x 14.8" (917 x 207 x 375 mm) |
| Drivers | 1" titanium tweeter with Tractrix horn, dual 5.25" cerametallic woofers |
| Frequency Response | 40Hz - 25kHz (+-3dB, Manufacturer specified) |
| Impedance | 8 ohms nominal, 3.3 ohms minimum (measured above 80Hz, Erin's Audio Corner) |
| Output Power | 100W continuous, 400W peak |
| Sensitivity | 90dB (2.83V/1m, measured by Erin's Audio Corner) |
| Weight | 38.6 lbs / 17.5 kg |
| Woofer Cabinet | ported, rear |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- Klipsch RP-5000F II vs SVS Ultra Evolution Pinnacle
- Klipsch RP-5000F II vs KEF Q11 Meta
- Klipsch RP-5000F II vs Monolith THX-365T
- Klipsch RP-5000F II vs Klipsch RP-8000F II
- Klipsch RP-5000F II vs Klipsch Heresy IV
- Klipsch RP-5000F II vs Dynaudio Emit 30
- Klipsch RP-5000F II vs Polk Audio XT60
- Klipsch RP-5000F II vs Klipsch RP-6000F II
- See all 26 comparisons