Short answer: the MoFi SourcePoint 10 on measured sound quality, the Philharmonic BMR (v1) on price. The MoFi SourcePoint 10 ranks #26 of 130 bookshelf speakers at $3795. The Philharmonic BMR (v1) ranks #36 at $2200, $1595 cheaper.
What the MoFi SourcePoint 10 offers: Andrew Jones-designed concentric/coincident driver delivers best-in-class sound power and early-reflections directivity in the reviewer’s testing - a genuine “point source” design. Vertical and horizontal radiation patterns closely match each other (about ±50° horizontal, ±30-40° vertical), a hallmark benefit of a well-executed concentric driver. Distortion stays low - under 1% above 100Hz at 86dB, and under 3% up to 100Hz even at 96dB, better than the reviewer expected from a low-excursion waveguide-loaded woofer. Surprisingly strong dynamic capability with little audible compression at both low and high volume. Widely spaced (about 11 feet apart) with roughly 15° of toe-out produced a huge, expansive soundstage without significant loss of imaging precision. Solidly built cabinet (about 40 lbs, heavily braced) minimizes cabinet resonance. Watch for: Like virtually all coincident designs, sounds notably bright pointed directly on-axis due to a deliberate treble lift (meant to compensate for the 28mm tweeter’s earlier beaming versus a typical 25mm/1” tweeter) combined with a diffraction dip/peak from the waveguide edge; needs about 15° of toe-out to sound neutral, and even then benefits from an extra 1-2dB of treble EQ. Toeing out further (to 30°) flattens the treble further but introduces a dip in the midrange-to-tweeter crossover region - there’s no single toe-out angle that fixes everything at once. F3 of 56Hz and F10 of 38Hz (about 40Hz in-room) mean genuine deep bass is limited; the reviewer would pair it with a sealed 10” or 12” subwoofer for regular daily listening. Bass extension and cabinet placement trade off against midrange cleanliness: placing it close to a wall for more bass risks a wall-bounce suckout in the midrange (roughly 200-500Hz depending on distance). Not perfectly time-aligned between tweeter and woofer (about 0.4ms delta), an inherent limitation of passive coincident drivers versus actively time-corrected designs. Some resonances appear in measurements, likely port-related. Minimum impedance around 6.4 ohms with EPDR near 3 ohms, so the reviewer recommends sticking with a 4-ohm-rated amplifier to be safe.
What the Philharmonic BMR (v1) offers: Large three-way combining a Scan-Speak 7-inch paper/carbon woofer, 2.5-inch Tectonic balanced-mode midrange and RAAL 64-10 ribbon. Erin measured approximately +/-1.5dB linearity from 80Hz upward, very broad +/-40-degree-or-better horizontal coverage and about 83dB/2.83V/1m sensitivity. The port is tuned in the mid/low-30Hz region without audible chuffing, the midrange provides unusually expansive staging, and distortion remained subjectively unobtrusive. Watch for: The measured 83dB sensitivity and roughly 4-ohm load demand meaningful external amplification. A 1-2dB shelf below about 300Hz reduces warmth unless corrected, while a response/impedance feature near 250-300Hz corresponded with Erin’s sense of resonance. The ribbon produces narrower vertical than horizontal radiation, and second-order high-frequency distortion plus dynamic enhancement near 3kHz appeared in testing. This was an earlier cabinet/version, not the current v2.
Buy the MoFi SourcePoint 10 if sound quality is the priority over the price, or the Philharmonic BMR (v1) if the price is the priority over sound quality.
Still deciding? The full Passive Home rankings cover every ranked option.
Specifications Side By Side
| MoFi SourcePoint 10 | Philharmonic BMR (v1) | |
|---|---|---|
| Price | $3795 per pair | $2,395 per pair |
| Ranked | #26 of 130 in Large Size Bookshelf Speakers | #36 of 130 in Large Size Bookshelf Speakers |
| Bass Extension (-10dB) | 38Hz (measured, Erin's Audio Corner) | 37.8Hz (measured, Erin's Audio Corner) |
| Bass Extension (-3dB) | 56Hz (measured, Erin's Audio Corner) | Approximately 62Hz relative to mean (measured, Erin's Audio Corner website) |
| Dimensions | 22.5"H x 14.5"W x 16.6"D (571.5 x 368.3 x 421.6 mm) | - |
| Impedance | 8 ohms nominal, 6.4 ohms minimum (measured, Erin's Audio Corner) | Approximately 4 ohms nominal (measured, Erin's Audio Corner) |
| Sensitivity | 88.2dB (measured, Erin's Audio Corner) | Approximately 83dB/2.83V/1m (measured, Erin's Audio Corner) |
| Drivers | 10" Paper-pulp Cone woofer, 1.25-inch soft-dome tweeter | RAAL 64-10 ribbon; 2.5" BMR midrange; 7" Scan-Speak woofer |
| Weight | 46.3 lbs (21.0 kg) each | - |
| Woofer Cabinet | ported, rear | ported |
| Spinorama Preference Score | 3.25 | 5.24 |
| Spinorama Preference Score with Perfect Sub | 5.27 | 6.90 |
| Port Tuning | - | Mid/low-30Hz range (measured, Erin's Audio Corner) |
Related Speaker Comparisons
How MoFi SourcePoint 10 compares with other leading options:
- MoFi SourcePoint 10 vs Perlisten S4b
- KEF Reference 1 Meta vs MoFi SourcePoint 10
- GR-Research NX-Studio vs MoFi SourcePoint 10
- AsciLab C6B vs MoFi SourcePoint 10
- Audio First Cadentia 3 vs MoFi SourcePoint 10
Prices on this page were last checked September 16, 2026 at 12:41 AM UTC. Product prices and availability are accurate as of that date/time and are subject to change; the price and availability shown on Amazon at the time of purchase will apply to the purchase of this product.
As an eBay Partner, we may be compensated if you make a purchase.
The Two Speakers In Full
MoFi SourcePoint 10: $3795 per pair Crutchfield eBay
Pros: Andrew Jones-designed concentric/coincident driver delivers best-in-class sound power and early-reflections directivity in the reviewer’s testing - a genuine “point source” design. Vertical and horizontal radiation patterns closely match each other (about ±50° horizontal, ±30-40° vertical), a hallmark benefit of a well-executed concentric driver. Distortion stays low - under 1% above 100Hz at 86dB, and under 3% up to 100Hz even at 96dB, better than the reviewer expected from a low-excursion waveguide-loaded woofer. Surprisingly strong dynamic capability with little audible compression at both low and high volume. Widely spaced (about 11 feet apart) with roughly 15° of toe-out produced a huge, expansive soundstage without significant loss of imaging precision. Solidly built cabinet (about 40 lbs, heavily braced) minimizes cabinet resonance. Measured bass extension of 56Hz (-3dB), with a measured sensitivity of 88.2dB.
Cons: Like virtually all coincident designs, sounds notably bright pointed directly on-axis due to a deliberate treble lift (meant to compensate for the 28mm tweeter’s earlier beaming versus a typical 25mm/1” tweeter) combined with a diffraction dip/peak from the waveguide edge; needs about 15° of toe-out to sound neutral, and even then benefits from an extra 1-2dB of treble EQ. Toeing out further (to 30°) flattens the treble further but introduces a dip in the midrange-to-tweeter crossover region - there’s no single toe-out angle that fixes everything at once. F3 of 56Hz and F10 of 38Hz (about 40Hz in-room) mean genuine deep bass is limited; the reviewer would pair it with a sealed 10” or 12” subwoofer for regular daily listening. Bass extension and cabinet placement trade off against midrange cleanliness: placing it close to a wall for more bass risks a wall-bounce suckout in the midrange (roughly 200-500Hz depending on distance). Not perfectly time-aligned between tweeter and woofer (about 0.4ms delta), an inherent limitation of passive coincident drivers versus actively time-corrected designs. Some resonances appear in measurements, likely port-related. Minimum impedance around 6.4 ohms with EPDR near 3 ohms, so the reviewer recommends sticking with a 4-ohm-rated amplifier to be safe.
Full MoFi SourcePoint 10 review and specifications →
| Bass Extension (-10dB) | 38Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 56Hz (measured, Erin's Audio Corner) |
| Dimensions | 22.5"H x 14.5"W x 16.6"D (571.5 x 368.3 x 421.6 mm) |
| Drivers | 10" Paper-pulp Cone woofer, 1.25-inch soft-dome tweeter |
| Impedance | 8 ohms nominal, 6.4 ohms minimum (measured, Erin's Audio Corner) |
| Sensitivity | 88.2dB (measured, Erin's Audio Corner) |
| Spinorama Preference Score | 3.25 |
| Spinorama Preference Score with Perfect Sub | 5.27 |
| Weight | 46.3 lbs (21.0 kg) each |
| Woofer Cabinet | ported, rear |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- MoFi SourcePoint 10 vs Radiant Acoustics Clarity 6.2
- MoFi SourcePoint 10 vs Wharfedale Super Linton
- MoFi SourcePoint 10 vs Dynaudio Heritage Special
- MoFi SourcePoint 10 vs Ascend Acoustics CMT-340 SE2
- MoFi SourcePoint 10 vs Arendal 1528 Monitor 8
- MoFi SourcePoint 10 vs Wharfedale Linton 85
- MoFi SourcePoint 10 vs AsciLab F6Bs
- MoFi SourcePoint 10 vs Ascend Acoustics Sierra-LX
- See all 48 comparisons
Philharmonic BMR (v1): $2,395 per pair Philharmonic Audio eBay
Pros: Large three-way combining a Scan-Speak 7-inch paper/carbon woofer, 2.5-inch Tectonic balanced-mode midrange and RAAL 64-10 ribbon. Erin measured approximately +/-1.5dB linearity from 80Hz upward, very broad +/-40-degree-or-better horizontal coverage and about 83dB/2.83V/1m sensitivity. The port is tuned in the mid/low-30Hz region without audible chuffing, the midrange provides unusually expansive staging, and distortion remained subjectively unobtrusive. Measured bass extension of 62Hz (-3dB), with a measured sensitivity of 83dB.
Cons: The measured 83dB sensitivity and roughly 4-ohm load demand meaningful external amplification. A 1-2dB shelf below about 300Hz reduces warmth unless corrected, while a response/impedance feature near 250-300Hz corresponded with Erin’s sense of resonance. The ribbon produces narrower vertical than horizontal radiation, and second-order high-frequency distortion plus dynamic enhancement near 3kHz appeared in testing. This was an earlier cabinet/version, not the current v2.
Full Philharmonic BMR (v1) review and specifications →
| Bass Extension (-10dB) | 37.8Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | Approximately 62Hz relative to mean (measured, Erin's Audio Corner website) |
| Drivers | RAAL 64-10 ribbon; 2.5" BMR midrange; 7" Scan-Speak woofer |
| Impedance | Approximately 4 ohms nominal (measured, Erin's Audio Corner) |
| Port Tuning | Mid/low-30Hz range (measured, Erin's Audio Corner) |
| Sensitivity | Approximately 83dB/2.83V/1m (measured, Erin's Audio Corner) |
| Spinorama Preference Score | 5.24 |
| Spinorama Preference Score with Perfect Sub | 6.90 |
| Woofer Cabinet | ported |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- Philharmonic BMR (v1) vs ELAC VELA BS 403
- Philharmonic BMR (v1) vs Selah Audio Integrity
- Philharmonic BMR (v1) vs Ascend Acoustics Sierra-2EX V2
- Philharmonic BMR (v1) vs Ascend Acoustics Sierra-LX
- Philharmonic BMR (v1) vs Wharfedale Linton 85
- Philharmonic BMR (v1) vs Emotiva Airmotiv XB2
- Philharmonic BMR (v1) vs ELAC Debut 3.0 DB63
- Philharmonic BMR (v1) vs Selah Audio Purezza
- See all 49 comparisons