Short answer: the KEF Reference 1 Meta if sound quality matters most, the MoFi SourcePoint 10 if price matters most. The KEF Reference 1 Meta ranks #3 of 130 bookshelf speakers at $9999.98. The MoFi SourcePoint 10 ranks #26 at $3795, $6204.98 cheaper.
What the KEF Reference 1 Meta offers: Meta technology places a Helmholtz-style resonator behind the tweeter to absorb rear-radiated resonance, and pair matching is within about ±0.5dB - unusually tight for a passive speaker. Sounds most neutral pointed straight on-axis rather than toed out, with no 5-8kHz harshness of the kind that plagues many speakers marketed as “detailed.” One of the most three-dimensional soundstages the reviewer has heard from a passive speaker, beaten only by $13,000+ active Xmachina Pulsar MK2 monitors (though this speaker’s tonality was preferred). Distortion stays below 1% down to about 70Hz at 86dB, and below 1% to ~150Hz / below 3% to ~70Hz even at 96dB. High-frequency response holds essentially flat as volume increases - no audible crossover or voice-coil compression - giving strong dynamic range up to its output limit (about 98dB at 3.5 meters before the woofer starts running out of excursion). All-passive design still measures ±1.5dB from 80Hz to 16kHz with zero DSP. Swappable dual-port system (long port for near-wall placement, short port for out-into-the-room placement with more bass extension) lets you tune bass behavior to where the speaker actually sits. Watch for: At roughly $9,000/pair, nearly four times the cost of the similarly-sized KEF R3. Radiation narrows from about ±60° in the midrange to ±50° at high frequency - tighter than the reviewer’s ~70° preference (though wider than the R3’s ~±40°); toeing the speakers out for more width sacrifices treble energy that then needs EQ to restore. Moderate-to-low sensitivity (measured 83-84dB) calls for a solid amplifier. In-room bass only extends to about 40Hz, so a subwoofer is worth adding for bass-heavy material at higher volumes or listening beyond 3-4 meters. Minor directivity mismatch around 2kHz shows up in measurements, likely a vertical diffraction effect that wasn’t fully explained. Bass port choice (long vs. short) meaningfully changes the sound depending on placement, so the wrong port for your room can leave the bass sounding off until you experiment.
What the MoFi SourcePoint 10 offers: Andrew Jones-designed concentric/coincident driver delivers best-in-class sound power and early-reflections directivity in the reviewer’s testing - a genuine “point source” design. Vertical and horizontal radiation patterns closely match each other (about ±50° horizontal, ±30-40° vertical), a hallmark benefit of a well-executed concentric driver. Distortion stays low - under 1% above 100Hz at 86dB, and under 3% up to 100Hz even at 96dB, better than the reviewer expected from a low-excursion waveguide-loaded woofer. Surprisingly strong dynamic capability with little audible compression at both low and high volume. Widely spaced (about 11 feet apart) with roughly 15° of toe-out produced a huge, expansive soundstage without significant loss of imaging precision. Solidly built cabinet (about 40 lbs, heavily braced) minimizes cabinet resonance. Watch for: Like virtually all coincident designs, sounds notably bright pointed directly on-axis due to a deliberate treble lift (meant to compensate for the 28mm tweeter’s earlier beaming versus a typical 25mm/1” tweeter) combined with a diffraction dip/peak from the waveguide edge; needs about 15° of toe-out to sound neutral, and even then benefits from an extra 1-2dB of treble EQ. Toeing out further (to 30°) flattens the treble further but introduces a dip in the midrange-to-tweeter crossover region - there’s no single toe-out angle that fixes everything at once. F3 of 56Hz and F10 of 38Hz (about 40Hz in-room) mean genuine deep bass is limited; the reviewer would pair it with a sealed 10” or 12” subwoofer for regular daily listening. Bass extension and cabinet placement trade off against midrange cleanliness: placing it close to a wall for more bass risks a wall-bounce suckout in the midrange (roughly 200-500Hz depending on distance). Not perfectly time-aligned between tweeter and woofer (about 0.4ms delta), an inherent limitation of passive coincident drivers versus actively time-corrected designs. Some resonances appear in measurements, likely port-related. Minimum impedance around 6.4 ohms with EPDR near 3 ohms, so the reviewer recommends sticking with a 4-ohm-rated amplifier to be safe.
Buy the KEF Reference 1 Meta if sound quality matters more than the price. Buy the MoFi SourcePoint 10 if the price matters more than sound quality.
Still deciding? The full Passive Home rankings cover every ranked option.
Specifications Side By Side
| KEF Reference 1 Meta | MoFi SourcePoint 10 | |
|---|---|---|
| Price | $10000 per pair | $3795 per pair |
| Ranked | #3 of 130 in Large Size Bookshelf Speakers | #26 of 130 in Large Size Bookshelf Speakers |
| Bass Extension (-10dB) | 32Hz (measured, Erin's Audio Corner) | 38Hz (measured, Erin's Audio Corner) |
| Bass Extension (-3dB) | 52Hz (measured, Erin's Audio Corner) | 56Hz (measured, Erin's Audio Corner) |
| Dimensions | 17.3"H x 8.1"W x 16.6"D (439.4 x 205.7 x 421.6 mm) | 22.5"H x 14.5"W x 16.6"D (571.5 x 368.3 x 421.6 mm) |
| Impedance | 4 ohms nominal, 2.9 ohms minimum (measured, Erin's Audio Corner) | 8 ohms nominal, 6.4 ohms minimum (measured, Erin's Audio Corner) |
| Drivers | 165 mm (6.5 in.) aluminium cone woofer, 125 mm (5 in.) aluminium cone midrange, 25 mm (1 in.) aluminium dome with MAT tweeter | 10" Paper-pulp Cone woofer, 1.25-inch soft-dome tweeter |
| Sensitivity | 82.5dB (measured average, Erin's Audio Corner) | 88.2dB (measured, Erin's Audio Corner) |
| Weight | 40.1 lbs (18.2 kg) each | 46.3 lbs (21.0 kg) each |
| Woofer Cabinet | ported, rear | ported, rear |
| Spinorama Preference Score | 5.84 | 3.25 |
| Spinorama Preference Score with Perfect Sub | 7.65 | 5.27 |
Related Speaker Comparisons
How KEF Reference 1 Meta compares with other leading options:
- Perlisten S4b vs KEF Reference 1 Meta
- GR-Research NX-Studio vs KEF Reference 1 Meta
- KEF Reference 1 Meta vs March Audio Sointuva AWG
- AsciLab C6B vs KEF Reference 1 Meta
- Audio First Cadentia 3 vs KEF Reference 1 Meta
Prices on this page were last checked September 16, 2026 at 12:41 AM UTC. Product prices and availability are accurate as of that date/time and are subject to change; the price and availability shown on Amazon at the time of purchase will apply to the purchase of this product.
As an eBay Partner, we may be compensated if you make a purchase.
The Two Speakers In Full
KEF Reference 1 Meta: $10000 per pair Kef eBay
Pros: Meta technology places a Helmholtz-style resonator behind the tweeter to absorb rear-radiated resonance, and pair matching is within about ±0.5dB - unusually tight for a passive speaker. Sounds most neutral pointed straight on-axis rather than toed out, with no 5-8kHz harshness of the kind that plagues many speakers marketed as “detailed.” One of the most three-dimensional soundstages the reviewer has heard from a passive speaker, beaten only by $13,000+ active Xmachina Pulsar MK2 monitors (though this speaker’s tonality was preferred). Distortion stays below 1% down to about 70Hz at 86dB, and below 1% to ~150Hz / below 3% to ~70Hz even at 96dB. High-frequency response holds essentially flat as volume increases - no audible crossover or voice-coil compression - giving strong dynamic range up to its output limit (about 98dB at 3.5 meters before the woofer starts running out of excursion). All-passive design still measures ±1.5dB from 80Hz to 16kHz with zero DSP. Swappable dual-port system (long port for near-wall placement, short port for out-into-the-room placement with more bass extension) lets you tune bass behavior to where the speaker actually sits. Measured bass extension of 52Hz (-3dB), with a measured sensitivity of 82.5dB.
Cons: At roughly $9,000/pair, nearly four times the cost of the similarly-sized KEF R3. Radiation narrows from about ±60° in the midrange to ±50° at high frequency - tighter than the reviewer’s ~70° preference (though wider than the R3’s ~±40°); toeing the speakers out for more width sacrifices treble energy that then needs EQ to restore. Moderate-to-low sensitivity (measured 83-84dB) calls for a solid amplifier. In-room bass only extends to about 40Hz, so a subwoofer is worth adding for bass-heavy material at higher volumes or listening beyond 3-4 meters. Minor directivity mismatch around 2kHz shows up in measurements, likely a vertical diffraction effect that wasn’t fully explained. Bass port choice (long vs. short) meaningfully changes the sound depending on placement, so the wrong port for your room can leave the bass sounding off until you experiment.
Full KEF Reference 1 Meta review and specifications →
| Bass Extension (-10dB) | 32Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 52Hz (measured, Erin's Audio Corner) |
| Dimensions | 17.3"H x 8.1"W x 16.6"D (439.4 x 205.7 x 421.6 mm) |
| Drivers | 165 mm (6.5 in.) aluminium cone woofer, 125 mm (5 in.) aluminium cone midrange, 25 mm (1 in.) aluminium dome with MAT tweeter |
| Impedance | 4 ohms nominal, 2.9 ohms minimum (measured, Erin's Audio Corner) |
| Sensitivity | 82.5dB (measured average, Erin's Audio Corner) |
| Spinorama Preference Score | 5.84 |
| Spinorama Preference Score with Perfect Sub | 7.65 |
| Weight | 40.1 lbs (18.2 kg) each |
| Woofer Cabinet | ported, rear |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- KEF Reference 1 Meta vs GR-Research NX-Studio
- KEF Reference 1 Meta vs Perlisten S4b
- KEF Reference 1 Meta vs March Audio Sointuva AWG
- KEF Reference 1 Meta vs AsciLab C6B
- KEF Reference 1 Meta vs Audio First Cadentia 3
- KEF Reference 1 Meta vs Revel M106
- KEF Reference 1 Meta vs KEF R3 Meta
- KEF Reference 1 Meta vs KEF Q Concerto Meta
- See all 46 comparisons
MoFi SourcePoint 10: $3795 per pair Crutchfield eBay
Pros: Andrew Jones-designed concentric/coincident driver delivers best-in-class sound power and early-reflections directivity in the reviewer’s testing - a genuine “point source” design. Vertical and horizontal radiation patterns closely match each other (about ±50° horizontal, ±30-40° vertical), a hallmark benefit of a well-executed concentric driver. Distortion stays low - under 1% above 100Hz at 86dB, and under 3% up to 100Hz even at 96dB, better than the reviewer expected from a low-excursion waveguide-loaded woofer. Surprisingly strong dynamic capability with little audible compression at both low and high volume. Widely spaced (about 11 feet apart) with roughly 15° of toe-out produced a huge, expansive soundstage without significant loss of imaging precision. Solidly built cabinet (about 40 lbs, heavily braced) minimizes cabinet resonance. Measured bass extension of 56Hz (-3dB), with a measured sensitivity of 88.2dB.
Cons: Like virtually all coincident designs, sounds notably bright pointed directly on-axis due to a deliberate treble lift (meant to compensate for the 28mm tweeter’s earlier beaming versus a typical 25mm/1” tweeter) combined with a diffraction dip/peak from the waveguide edge; needs about 15° of toe-out to sound neutral, and even then benefits from an extra 1-2dB of treble EQ. Toeing out further (to 30°) flattens the treble further but introduces a dip in the midrange-to-tweeter crossover region - there’s no single toe-out angle that fixes everything at once. F3 of 56Hz and F10 of 38Hz (about 40Hz in-room) mean genuine deep bass is limited; the reviewer would pair it with a sealed 10” or 12” subwoofer for regular daily listening. Bass extension and cabinet placement trade off against midrange cleanliness: placing it close to a wall for more bass risks a wall-bounce suckout in the midrange (roughly 200-500Hz depending on distance). Not perfectly time-aligned between tweeter and woofer (about 0.4ms delta), an inherent limitation of passive coincident drivers versus actively time-corrected designs. Some resonances appear in measurements, likely port-related. Minimum impedance around 6.4 ohms with EPDR near 3 ohms, so the reviewer recommends sticking with a 4-ohm-rated amplifier to be safe.
Full MoFi SourcePoint 10 review and specifications →
| Bass Extension (-10dB) | 38Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 56Hz (measured, Erin's Audio Corner) |
| Dimensions | 22.5"H x 14.5"W x 16.6"D (571.5 x 368.3 x 421.6 mm) |
| Drivers | 10" Paper-pulp Cone woofer, 1.25-inch soft-dome tweeter |
| Impedance | 8 ohms nominal, 6.4 ohms minimum (measured, Erin's Audio Corner) |
| Sensitivity | 88.2dB (measured, Erin's Audio Corner) |
| Spinorama Preference Score | 3.25 |
| Spinorama Preference Score with Perfect Sub | 5.27 |
| Weight | 46.3 lbs (21.0 kg) each |
| Woofer Cabinet | ported, rear |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- MoFi SourcePoint 10 vs Radiant Acoustics Clarity 6.2
- MoFi SourcePoint 10 vs Wharfedale Super Linton
- MoFi SourcePoint 10 vs Dynaudio Heritage Special
- MoFi SourcePoint 10 vs Ascend Acoustics CMT-340 SE2
- MoFi SourcePoint 10 vs Arendal 1528 Monitor 8
- MoFi SourcePoint 10 vs Wharfedale Linton 85
- MoFi SourcePoint 10 vs AsciLab F6Bs
- MoFi SourcePoint 10 vs Ascend Acoustics Sierra-LX
- See all 48 comparisons