Short answer: the Klipsch RP-8000F II for dynamics, unless you need deeper bass. Its ~92dB measured sensitivity is the highest in the RP II floorstander line and it had the best dynamics and compression behavior of the three under load, but mid-bass sounds lean and it did not reach the expected 50Hz in-room. The Dynaudio Emit 30 uses two 5.25” mid-woofers and dual rear ports, with a dip from roughly 2-5kHz that makes the top end uneven.
Buy the Klipsch RP-8000F II. Both are rated the same for sound quality, and it costs $114.27 less than the Dynaudio Emit 30.
Still deciding? The full Passive Home rankings cover every ranked option.
Specifications Side By Side
| Klipsch RP-8000F II | Dynaudio Emit 30 | |
|---|---|---|
| Price | $1,159.98 per pair | $1,274.25 per pair |
| Ranked | #49 of 74 in Large Size Floorstanding Speakers | #50 of 74 in Large Size Floorstanding Speakers |
| Bass Extension (-10dB) | 33Hz (measured, Erin’s Audio Corner) | 36Hz (measured, Erin’s Audio Corner) |
| Bass Extension (-3dB) | 67Hz (measured, Erin’s Audio Corner) | 44Hz (measured, Erin’s Audio Corner) |
| Sensitivity | 92dB (2.83V/1m, measured by Erin’s Audio Corner) | 87dB |
| Drivers | 1” titanium tweeter with 90x90 Tractrix horn, dual 8” cerametallic woofers | Dual 5.25” mid-woofers, 1” soft dome tweeter |
| Weight | 61.3 lbs (27.8 kg) | 34.2 lbs (15.5 kg) |
| Impedance | 8 ohms nominal (3.7 ohms minimum above 80Hz, measured by Erin’s Audio Corner) | 4 ohms |
| Frequency Response | 35Hz - 25kHz (+-3dB, Manufacturer specified) | 44Hz - 25kHz (±3dB, manufacturer specified) |
| Crossover Frequency | 1630Hz | - |
| Power Handling | 150W continuous, 600W peak | 180W (IEC rated) |
| Dimensions | 43.1” x 10.8” x 18.3” (1095 x 275 x 464 mm) | 35.4”H x 6.7”W x 10.7”D (900.0 x 170.0 x 272.0 mm) |
| Woofer Cabinet | ported, rear | ported, rear (dual) |
| Spinorama Preference Score | 5.39 | 3.84 |
| Spinorama Preference Score with Perfect Sub | 7.12 | 5.69 |
| DIY Kit | No | No |
| Country | - | Denmark |
Related Speaker Comparisons
More top alternatives to Klipsch RP-8000F II:
- Klipsch RP-8000F II vs KEF Blade Two Meta
- Klipsch RP-8000F II vs MoFi SourcePoint V10 Master Edition
- Klipsch RP-8000F II vs MoFi SourcePoint 888
- Klipsch RP-8000F II vs Revel F328Be
- Klipsch RP-8000F II vs Radiant Acoustics Clarity 66
Prices on this page were last checked October 2, 2026 at 10:18 PM UTC. Product prices and availability are accurate as of that date/time and are subject to change; the price and availability shown on Amazon at the time of purchase will apply to the purchase of this product.
As an eBay Partner, we may be compensated if you make a purchase.
The Two Speakers In Full
Klipsch RP-8000F II: $1,159.98 per pair Amazon eBay
Pros: Highest sensitivity of the RP II floorstander line (~92dB measured) and the best dynamics/compression behavior of the three under load: the cleanest at high output. Dual 8-inch woofers and the highest power handling in the line. Measured bass extension of 67Hz (-3dB), with a measured sensitivity of 92dB.
Cons: Mid-bass sounds lean despite the dual 8-inch woofers, and bass extension disappointed for its size: expected to reach 50Hz, didn’t get there in-room. Has its own edgy upper-mid bump (2-6kHz) that’s harder to EQ out than the other two models’ issues, since it stems from the vertical horn/woofer offset rather than simple tonal balance. The most placement-critical of the three, with the narrowest horizontal (~40-50 degrees) and vertical (+5/-10 degrees) dispersion.
Full Klipsch RP-8000F II review and specifications →
| Bass Extension (-10dB) | 33Hz (measured, Erin’s Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 67Hz (measured, Erin’s Audio Corner) |
| Crossover Frequency | 1630Hz |
| DIY Kit | No |
| Dimensions | 43.1” x 10.8” x 18.3” (1095 x 275 x 464 mm) |
| Drivers | 1” titanium tweeter with 90x90 Tractrix horn, dual 8” cerametallic woofers |
| Frequency Response | 35Hz - 25kHz (+-3dB, Manufacturer specified) |
| Impedance | 8 ohms nominal (3.7 ohms minimum above 80Hz, measured by Erin’s Audio Corner) |
| Power Handling | 150W continuous, 600W peak |
| Sensitivity | 92dB (2.83V/1m, measured by Erin’s Audio Corner) |
| Spinorama Preference Score | 5.39 |
| Spinorama Preference Score with Perfect Sub | 7.12 |
| Weight | 61.3 lbs (27.8 kg) |
| Woofer Cabinet | ported, rear |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- Klipsch RP-8000F II vs Klipsch RP-6000F II
- Klipsch RP-8000F II vs Klipsch RP-5000F II
- Klipsch RP-8000F II vs Definitive Technology BP-9020
- Klipsch RP-8000F II vs KLH Model Five
- Klipsch RP-8000F II vs SVS Ultra Evolution Pinnacle
- Klipsch RP-8000F II vs KEF Q11 Meta
- Klipsch RP-8000F II vs Polk T50
- Klipsch RP-8000F II vs Klipsch Forte IV
- See all 44 comparisons
Dynaudio Emit 30: $1,274.25 per pair Amazon eBay
Pros: A 2.5-way floorstander: two 5.25” mid-woofers paired with a roughly 1” dome tweeter, driven through dual rear bass-reflex ports. The two woofers hand off at staggered crossover points (around 1kHz and 3.5kHz) rather than sharing one, which avoids the acoustic lobing a shared crossover point would cause between the tweeter and the lower woofer, and adds a few dB of sensitivity in the process. Genuinely deep bass for a speaker around this price: measured F3 near 44Hz and extends audibly down to about 40Hz in-room without much difficulty. Harmonic distortion measures clean and low at both 86dB and 96dB SPL/1m. Good CTA-2034 sound power and uniform directivity mean the speaker takes EQ correction well if a listener wants to dial in its one tonal weak point. Dynamic range and compression performance are strong overall, with only a minor, high-Q compression artifact tied to a cone-edge resonance that’s unlikely to be audible. Wide, consistent horizontal dispersion around ±70° with just a small ~10° narrowing between 1-3kHz, and a reasonably forgiving ±20° vertical window centered on the tweeter axis. Measured bass extension of 44Hz (-3dB).
Cons: A dip and inconsistency in the lower-treble presence region (roughly 2-5kHz) makes the top end sound uneven (sometimes soft, sometimes forward) depending on the specific instrument or frequency being reproduced; male vocals can lack presence and cymbals can lack sizzle as a result. A cone-edge surround resonance shows up around 1-1.3kHz in burst-decay measurements (a trait the reviewer has also seen on other Dynaudio models) and lines up with elevated multitone distortion across roughly 600Hz-1.5kHz. An enclosure resonance appears around 350Hz in the impedance curve. Placed too close to a rear wall, the dual ports make the bass noticeably boomy: pulling the speaker out is needed to keep the low end from overloading the room. Fully resolving the top-end inconsistency needs a modest EQ correction (roughly +2dB with a Q of about 1, centered 3-6kHz), so out-of-the-box tonal accuracy in that band isn’t quite class-leading despite otherwise strong measured performance.
Full Dynaudio Emit 30 review and specifications →
| Bass Extension (-10dB) | 36Hz (measured, Erin’s Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 44Hz (measured, Erin’s Audio Corner) |
| Country | Denmark |
| DIY Kit | No |
| Dimensions | 35.4”H x 6.7”W x 10.7”D (900.0 x 170.0 x 272.0 mm) |
| Drivers | Dual 5.25” mid-woofers, 1” soft dome tweeter |
| Frequency Response | 44Hz - 25kHz (±3dB, manufacturer specified) |
| Impedance | 4 ohms |
| Power Handling | 180W (IEC rated) |
| Sensitivity | 87dB |
| Spinorama Preference Score | 3.84 |
| Spinorama Preference Score with Perfect Sub | 5.69 |
| Weight | 34.2 lbs (15.5 kg) |
| Woofer Cabinet | ported, rear (dual) |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- Dynaudio Emit 30 vs Klipsch RP-6000F II
- Dynaudio Emit 30 vs Definitive Technology BP-9020
- Dynaudio Emit 30 vs SVS Ultra Evolution Pinnacle
- Dynaudio Emit 30 vs Polk T50
- Dynaudio Emit 30 vs Klipsch RP-5000F II
- Dynaudio Emit 30 vs KEF Q11 Meta
- Dynaudio Emit 30 vs Focal Aria Evo X N°2
- Dynaudio Emit 30 vs Klipsch Forte IV
- See all 43 comparisons