Short answer: the MoFi SourcePoint 10. It ranks #26 of 130 bookshelf speakers by sound quality; the Mission LX-3 MKII ranks #80.
What the MoFi SourcePoint 10 offers: Andrew Jones-designed concentric/coincident driver delivers best-in-class sound power and early-reflections directivity in the reviewer’s testing - a genuine “point source” design. Vertical and horizontal radiation patterns closely match each other (about ±50° horizontal, ±30-40° vertical), a hallmark benefit of a well-executed concentric driver. Distortion stays low - under 1% above 100Hz at 86dB, and under 3% up to 100Hz even at 96dB, better than the reviewer expected from a low-excursion waveguide-loaded woofer. Surprisingly strong dynamic capability with little audible compression at both low and high volume. Widely spaced (about 11 feet apart) with roughly 15° of toe-out produced a huge, expansive soundstage without significant loss of imaging precision. Solidly built cabinet (about 40 lbs, heavily braced) minimizes cabinet resonance. Watch for: Like virtually all coincident designs, sounds notably bright pointed directly on-axis due to a deliberate treble lift (meant to compensate for the 28mm tweeter’s earlier beaming versus a typical 25mm/1” tweeter) combined with a diffraction dip/peak from the waveguide edge; needs about 15° of toe-out to sound neutral, and even then benefits from an extra 1-2dB of treble EQ. Toeing out further (to 30°) flattens the treble further but introduces a dip in the midrange-to-tweeter crossover region - there’s no single toe-out angle that fixes everything at once. F3 of 56Hz and F10 of 38Hz (about 40Hz in-room) mean genuine deep bass is limited; the reviewer would pair it with a sealed 10” or 12” subwoofer for regular daily listening. Bass extension and cabinet placement trade off against midrange cleanliness: placing it close to a wall for more bass risks a wall-bounce suckout in the midrange (roughly 200-500Hz depending on distance). Not perfectly time-aligned between tweeter and woofer (about 0.4ms delta), an inherent limitation of passive coincident drivers versus actively time-corrected designs. Some resonances appear in measurements, likely port-related. Minimum impedance around 6.4 ohms with EPDR near 3 ohms, so the reviewer recommends sticking with a 4-ohm-rated amplifier to be safe.
What the Mission LX-3 MKII offers: A large affordable standmount with a 6.5-inch woofer, 88dB rated sensitivity and useful bass. ASR measured 48Hz estimated in-room extension, a controlled Q of 0.60, a 5.52 subwoofer-assisted preference score and reasonable +/-55-degree horizontal coverage. Watch for: On-axis smoothness of 0.217 and predicted in-room smoothness of 0.344 reveal clear response unevenness, with a -0.46dB-per-octave downward tilt. The 345mm-tall, 8.4kg cabinet is bulky and current US availability is limited.
Buy the MoFi SourcePoint 10 if sound quality is the priority over the price, or the Mission LX-3 MKII if the price is the priority over sound quality.
Still deciding? The full Passive Home rankings cover every ranked option.
Specifications Side By Side
| MoFi SourcePoint 10 | Mission LX-3 MKII | |
|---|---|---|
| Price | $3795 per pair | £249 per pair |
| Ranked | #26 of 130 in Large Size Bookshelf Speakers | #80 of 130 in Large Size Bookshelf Speakers |
| Bass Extension (-10dB) | 38Hz (measured, Erin's Audio Corner) | - |
| Bass Extension (-3dB) | 56Hz (measured, Erin's Audio Corner) | - |
| Dimensions | 22.5"H x 14.5"W x 16.6"D (571.5 x 368.3 x 421.6 mm) | 13.6H x 8.9W x 12.1D in |
| Impedance | 8 ohms nominal, 6.4 ohms minimum (measured, Erin's Audio Corner) | 8 ohms nominal, 4.1 ohms minimum |
| Sensitivity | 88.2dB (measured, Erin's Audio Corner) | 88dB |
| Drivers | 10" Paper-pulp Cone woofer, 1.25-inch soft-dome tweeter | 1" microfiber-dome tweeter, 6.5" composite-fiber woofer |
| Weight | 46.3 lbs (21.0 kg) each | 18.5 lbs (8.4 kg) each |
| Woofer Cabinet | ported, rear | - |
| Spinorama Preference Score | 3.25 | 3.26 |
| Spinorama Preference Score with Perfect Sub | 5.27 | 5.52 |
| Enclosure | - | 2-way, bass-reflex |
| Country | - | United Kingdom (design) |
Related Speaker Comparisons
More top alternatives to MoFi SourcePoint 10:
- MoFi SourcePoint 10 vs Perlisten S4b
- KEF Reference 1 Meta vs MoFi SourcePoint 10
- GR-Research NX-Studio vs MoFi SourcePoint 10
- AsciLab C6B vs MoFi SourcePoint 10
- Audio First Cadentia 3 vs MoFi SourcePoint 10
Prices on this page were last checked September 16, 2026 at 12:41 AM UTC. Product prices and availability are accurate as of that date/time and are subject to change; the price and availability shown on Amazon at the time of purchase will apply to the purchase of this product.
As an eBay Partner, we may be compensated if you make a purchase.
The Two Speakers In Full
MoFi SourcePoint 10: $3795 per pair Crutchfield eBay
Pros: Andrew Jones-designed concentric/coincident driver delivers best-in-class sound power and early-reflections directivity in the reviewer’s testing - a genuine “point source” design. Vertical and horizontal radiation patterns closely match each other (about ±50° horizontal, ±30-40° vertical), a hallmark benefit of a well-executed concentric driver. Distortion stays low - under 1% above 100Hz at 86dB, and under 3% up to 100Hz even at 96dB, better than the reviewer expected from a low-excursion waveguide-loaded woofer. Surprisingly strong dynamic capability with little audible compression at both low and high volume. Widely spaced (about 11 feet apart) with roughly 15° of toe-out produced a huge, expansive soundstage without significant loss of imaging precision. Solidly built cabinet (about 40 lbs, heavily braced) minimizes cabinet resonance. Measured bass extension of 56Hz (-3dB), with a measured sensitivity of 88.2dB.
Cons: Like virtually all coincident designs, sounds notably bright pointed directly on-axis due to a deliberate treble lift (meant to compensate for the 28mm tweeter’s earlier beaming versus a typical 25mm/1” tweeter) combined with a diffraction dip/peak from the waveguide edge; needs about 15° of toe-out to sound neutral, and even then benefits from an extra 1-2dB of treble EQ. Toeing out further (to 30°) flattens the treble further but introduces a dip in the midrange-to-tweeter crossover region - there’s no single toe-out angle that fixes everything at once. F3 of 56Hz and F10 of 38Hz (about 40Hz in-room) mean genuine deep bass is limited; the reviewer would pair it with a sealed 10” or 12” subwoofer for regular daily listening. Bass extension and cabinet placement trade off against midrange cleanliness: placing it close to a wall for more bass risks a wall-bounce suckout in the midrange (roughly 200-500Hz depending on distance). Not perfectly time-aligned between tweeter and woofer (about 0.4ms delta), an inherent limitation of passive coincident drivers versus actively time-corrected designs. Some resonances appear in measurements, likely port-related. Minimum impedance around 6.4 ohms with EPDR near 3 ohms, so the reviewer recommends sticking with a 4-ohm-rated amplifier to be safe.
Full MoFi SourcePoint 10 review and specifications →
| Bass Extension (-10dB) | 38Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 56Hz (measured, Erin's Audio Corner) |
| Dimensions | 22.5"H x 14.5"W x 16.6"D (571.5 x 368.3 x 421.6 mm) |
| Drivers | 10" Paper-pulp Cone woofer, 1.25-inch soft-dome tweeter |
| Impedance | 8 ohms nominal, 6.4 ohms minimum (measured, Erin's Audio Corner) |
| Sensitivity | 88.2dB (measured, Erin's Audio Corner) |
| Spinorama Preference Score | 3.25 |
| Spinorama Preference Score with Perfect Sub | 5.27 |
| Weight | 46.3 lbs (21.0 kg) each |
| Woofer Cabinet | ported, rear |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- MoFi SourcePoint 10 vs Radiant Acoustics Clarity 6.2
- MoFi SourcePoint 10 vs Wharfedale Super Linton
- MoFi SourcePoint 10 vs Dynaudio Heritage Special
- MoFi SourcePoint 10 vs Ascend Acoustics CMT-340 SE2
- MoFi SourcePoint 10 vs Arendal 1528 Monitor 8
- MoFi SourcePoint 10 vs Wharfedale Linton 85
- MoFi SourcePoint 10 vs AsciLab F6Bs
- MoFi SourcePoint 10 vs Ascend Acoustics Sierra-LX
- See all 48 comparisons
Mission LX-3 MKII: £249 per pair Richer Sounds eBay
Pros: A large affordable standmount with a 6.5-inch woofer, 88dB rated sensitivity and useful bass. ASR measured 48Hz estimated in-room extension, a controlled Q of 0.60, a 5.52 subwoofer-assisted preference score and reasonable +/-55-degree horizontal coverage.
Cons: On-axis smoothness of 0.217 and predicted in-room smoothness of 0.344 reveal clear response unevenness, with a -0.46dB-per-octave downward tilt. The 345mm-tall, 8.4kg cabinet is bulky and current US availability is limited.
Full Mission LX-3 MKII review and specifications →
| Country | United Kingdom (design) |
|---|---|
| Dimensions | 13.6H x 8.9W x 12.1D in |
| Drivers | 1" microfiber-dome tweeter, 6.5" composite-fiber woofer |
| Enclosure | 2-way, bass-reflex |
| Impedance | 8 ohms nominal, 4.1 ohms minimum |
| Sensitivity | 88dB |
| Spinorama Preference Score | 3.26 |
| Spinorama Preference Score with Perfect Sub | 5.52 |
| Weight | 18.5 lbs (8.4 kg) each |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- Mission LX-3 MKII vs GR-Research X-LS Encore
- Mission LX-3 MKII vs Philharmonic BMR Monitor
- Mission LX-3 MKII vs Dynaudio Emit 20
- Mission LX-3 MKII vs Klipsch RP-600M II
- Mission LX-3 MKII vs Dynaudio Special Forty
- Mission LX-3 MKII vs ELAC Debut 2.0 B6.2
- Mission LX-3 MKII vs SVS Prime Bookshelf
- Mission LX-3 MKII vs KEF Q3 Meta
- See all 44 comparisons