Short answer: the MoFi SourcePoint 10 for better sound quality, the Dynaudio Emit 20 for the lower price. The MoFi SourcePoint 10 ranks #26 of 130 bookshelf speakers at $3795. The Dynaudio Emit 20 ranks #75 at $1049, $2746 cheaper.
What the MoFi SourcePoint 10 offers: Andrew Jones-designed concentric/coincident driver delivers best-in-class sound power and early-reflections directivity in the reviewer’s testing - a genuine “point source” design. Vertical and horizontal radiation patterns closely match each other (about ±50° horizontal, ±30-40° vertical), a hallmark benefit of a well-executed concentric driver. Distortion stays low - under 1% above 100Hz at 86dB, and under 3% up to 100Hz even at 96dB, better than the reviewer expected from a low-excursion waveguide-loaded woofer. Surprisingly strong dynamic capability with little audible compression at both low and high volume. Widely spaced (about 11 feet apart) with roughly 15° of toe-out produced a huge, expansive soundstage without significant loss of imaging precision. Solidly built cabinet (about 40 lbs, heavily braced) minimizes cabinet resonance. Watch for: Like virtually all coincident designs, sounds notably bright pointed directly on-axis due to a deliberate treble lift (meant to compensate for the 28mm tweeter’s earlier beaming versus a typical 25mm/1” tweeter) combined with a diffraction dip/peak from the waveguide edge; needs about 15° of toe-out to sound neutral, and even then benefits from an extra 1-2dB of treble EQ. Toeing out further (to 30°) flattens the treble further but introduces a dip in the midrange-to-tweeter crossover region - there’s no single toe-out angle that fixes everything at once. F3 of 56Hz and F10 of 38Hz (about 40Hz in-room) mean genuine deep bass is limited; the reviewer would pair it with a sealed 10” or 12” subwoofer for regular daily listening. Bass extension and cabinet placement trade off against midrange cleanliness: placing it close to a wall for more bass risks a wall-bounce suckout in the midrange (roughly 200-500Hz depending on distance). Not perfectly time-aligned between tweeter and woofer (about 0.4ms delta), an inherent limitation of passive coincident drivers versus actively time-corrected designs. Some resonances appear in measurements, likely port-related. Minimum impedance around 6.4 ohms with EPDR near 3 ohms, so the reviewer recommends sticking with a 4-ohm-rated amplifier to be safe.
What the Dynaudio Emit 20 offers: Two-way design with a 28mm Esotar soft dome tweeter (Hexis-damped) and an 18cm mid-woofer, using a first-order crossover on the tweeter and second-order on the woofer. Exceptional bass extension for a bookshelf speaker - reaches a clean, authoritative 40Hz in-room, rare enough that the reviewer says most listeners could skip a subwoofer for typical music. Very low distortion across the board, staying below 1% THD down to 40Hz at 86dB and below 3% even at 96dB - unusually clean bass performance where most two-way bookshelf speakers start rising in distortion around 80Hz. Wide, remarkably consistent horizontal directivity (about ±50-60°) that holds steady up to roughly 13kHz - rare for a speaker in this format, thanks to a beveled tweeter edge that acts as a mild waveguide. Excellent compression and dynamic-range linearity at the frequency extremes, actually showing slight bass enhancement rather than the sharp low-end compression common in similarly-sized bookshelf speakers. Watch for: A resonance around 600-800Hz gives snares and similar percussion a muffled, flat quality lacking impact - confirmed as originating in the woofer itself (isolated via measurements of the raw driver out of the cabinet), and attempts at constrained-layer damping didn’t resolve it. A peak around 4kHz adds a sharp, edgy quality to some male vocals. A roughly 5dB boost above 10kHz gives cymbals and hi-hats excess shimmer that can sound unnatural, especially pointed directly on-axis. Vertical dispersion shows two separate crossover-related notches (above and below the tweeter reference line around 5kHz) rather than the usual single one, a direct consequence of the shallow crossover slopes used on both drivers. Multitone distortion is elevated in the midrange, possibly due to the woofer’s magnet structure lacking a shorting ring. Best aimed slightly off-axis (about 10-15° of toe-out) to tame the excess high-frequency shimmer, rather than pointed straight at the listener.
Buy the MoFi SourcePoint 10 if sound quality matters more than the price. Buy the Dynaudio Emit 20 if the price matters more than sound quality.
Looking for alternatives? See the complete Passive Home rankings.
Specifications Side By Side
| MoFi SourcePoint 10 | Dynaudio Emit 20 | |
|---|---|---|
| Price | $3795 per pair | $1,049.00 per pair |
| Ranked | #26 of 130 in Large Size Bookshelf Speakers | #75 of 130 in Large Size Bookshelf Speakers |
| Bass Extension (-10dB) | 38Hz (measured, Erin's Audio Corner) | 33Hz (measured, Erin's Audio Corner) |
| Bass Extension (-3dB) | 56Hz (measured, Erin's Audio Corner) | 54Hz (measured, Erin's Audio Corner) |
| Dimensions | 22.5"H x 14.5"W x 16.6"D (571.5 x 368.3 x 421.6 mm) | 14.6"H x 8.1"W x 12.3"D (370.0 x 205.0 x 312.0 mm) |
| Impedance | 8 ohms nominal, 6.4 ohms minimum (measured, Erin's Audio Corner) | 6 ohms nominal (5.5 ohms minimum above 80Hz, measured, Erin's Audio Corner) |
| Sensitivity | 88.2dB (measured, Erin's Audio Corner) | 83.5dB (measured, Erin's Audio Corner; 86dB manufacturer specified) |
| Drivers | 10" Paper-pulp Cone woofer, 1.25-inch soft-dome tweeter | 7.1" Magnesium Silicate Polymer woofer, 1.1" Cerotar soft dome with Hexis tweeter |
| Weight | 46.3 lbs (21.0 kg) each | 12.8 lbs (5.8 kg) |
| Woofer Cabinet | ported, rear | ported, rear |
| Spinorama Preference Score | 3.25 | 3.35 |
| Spinorama Preference Score with Perfect Sub | 5.27 | 5.05 |
Related Speaker Comparisons
More worthwhile head-to-heads for MoFi SourcePoint 10:
- MoFi SourcePoint 10 vs Perlisten S4b
- KEF Reference 1 Meta vs MoFi SourcePoint 10
- GR-Research NX-Studio vs MoFi SourcePoint 10
- AsciLab C6B vs MoFi SourcePoint 10
- Audio First Cadentia 3 vs MoFi SourcePoint 10
Prices on this page were last checked September 16, 2026 at 12:41 AM UTC. Product prices and availability are accurate as of that date/time and are subject to change; the price and availability shown on Amazon at the time of purchase will apply to the purchase of this product.
As an eBay Partner, we may be compensated if you make a purchase.
The Two Speakers In Full
MoFi SourcePoint 10: $3795 per pair Crutchfield eBay
Pros: Andrew Jones-designed concentric/coincident driver delivers best-in-class sound power and early-reflections directivity in the reviewer’s testing - a genuine “point source” design. Vertical and horizontal radiation patterns closely match each other (about ±50° horizontal, ±30-40° vertical), a hallmark benefit of a well-executed concentric driver. Distortion stays low - under 1% above 100Hz at 86dB, and under 3% up to 100Hz even at 96dB, better than the reviewer expected from a low-excursion waveguide-loaded woofer. Surprisingly strong dynamic capability with little audible compression at both low and high volume. Widely spaced (about 11 feet apart) with roughly 15° of toe-out produced a huge, expansive soundstage without significant loss of imaging precision. Solidly built cabinet (about 40 lbs, heavily braced) minimizes cabinet resonance. Measured bass extension of 56Hz (-3dB), with a measured sensitivity of 88.2dB.
Cons: Like virtually all coincident designs, sounds notably bright pointed directly on-axis due to a deliberate treble lift (meant to compensate for the 28mm tweeter’s earlier beaming versus a typical 25mm/1” tweeter) combined with a diffraction dip/peak from the waveguide edge; needs about 15° of toe-out to sound neutral, and even then benefits from an extra 1-2dB of treble EQ. Toeing out further (to 30°) flattens the treble further but introduces a dip in the midrange-to-tweeter crossover region - there’s no single toe-out angle that fixes everything at once. F3 of 56Hz and F10 of 38Hz (about 40Hz in-room) mean genuine deep bass is limited; the reviewer would pair it with a sealed 10” or 12” subwoofer for regular daily listening. Bass extension and cabinet placement trade off against midrange cleanliness: placing it close to a wall for more bass risks a wall-bounce suckout in the midrange (roughly 200-500Hz depending on distance). Not perfectly time-aligned between tweeter and woofer (about 0.4ms delta), an inherent limitation of passive coincident drivers versus actively time-corrected designs. Some resonances appear in measurements, likely port-related. Minimum impedance around 6.4 ohms with EPDR near 3 ohms, so the reviewer recommends sticking with a 4-ohm-rated amplifier to be safe.
Full MoFi SourcePoint 10 review and specifications →
| Bass Extension (-10dB) | 38Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 56Hz (measured, Erin's Audio Corner) |
| Dimensions | 22.5"H x 14.5"W x 16.6"D (571.5 x 368.3 x 421.6 mm) |
| Drivers | 10" Paper-pulp Cone woofer, 1.25-inch soft-dome tweeter |
| Impedance | 8 ohms nominal, 6.4 ohms minimum (measured, Erin's Audio Corner) |
| Sensitivity | 88.2dB (measured, Erin's Audio Corner) |
| Spinorama Preference Score | 3.25 |
| Spinorama Preference Score with Perfect Sub | 5.27 |
| Weight | 46.3 lbs (21.0 kg) each |
| Woofer Cabinet | ported, rear |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- MoFi SourcePoint 10 vs Radiant Acoustics Clarity 6.2
- MoFi SourcePoint 10 vs Wharfedale Super Linton
- MoFi SourcePoint 10 vs Dynaudio Heritage Special
- MoFi SourcePoint 10 vs Ascend Acoustics CMT-340 SE2
- MoFi SourcePoint 10 vs Arendal 1528 Monitor 8
- MoFi SourcePoint 10 vs Wharfedale Linton 85
- MoFi SourcePoint 10 vs AsciLab F6Bs
- MoFi SourcePoint 10 vs Ascend Acoustics Sierra-LX
- See all 48 comparisons
Dynaudio Emit 20: $1,049.00 per pair Amazon eBay
Pros: Two-way design with a 28mm Esotar soft dome tweeter (Hexis-damped) and an 18cm mid-woofer, using a first-order crossover on the tweeter and second-order on the woofer. Exceptional bass extension for a bookshelf speaker - reaches a clean, authoritative 40Hz in-room, rare enough that the reviewer says most listeners could skip a subwoofer for typical music. Very low distortion across the board, staying below 1% THD down to 40Hz at 86dB and below 3% even at 96dB - unusually clean bass performance where most two-way bookshelf speakers start rising in distortion around 80Hz. Wide, remarkably consistent horizontal directivity (about ±50-60°) that holds steady up to roughly 13kHz - rare for a speaker in this format, thanks to a beveled tweeter edge that acts as a mild waveguide. Excellent compression and dynamic-range linearity at the frequency extremes, actually showing slight bass enhancement rather than the sharp low-end compression common in similarly-sized bookshelf speakers. Measured bass extension of 54Hz (-3dB), with a measured sensitivity of 83.5dB.
Cons: A resonance around 600-800Hz gives snares and similar percussion a muffled, flat quality lacking impact - confirmed as originating in the woofer itself (isolated via measurements of the raw driver out of the cabinet), and attempts at constrained-layer damping didn’t resolve it. A peak around 4kHz adds a sharp, edgy quality to some male vocals. A roughly 5dB boost above 10kHz gives cymbals and hi-hats excess shimmer that can sound unnatural, especially pointed directly on-axis. Vertical dispersion shows two separate crossover-related notches (above and below the tweeter reference line around 5kHz) rather than the usual single one, a direct consequence of the shallow crossover slopes used on both drivers. Multitone distortion is elevated in the midrange, possibly due to the woofer’s magnet structure lacking a shorting ring. Best aimed slightly off-axis (about 10-15° of toe-out) to tame the excess high-frequency shimmer, rather than pointed straight at the listener.
Full Dynaudio Emit 20 review and specifications →
| Bass Extension (-10dB) | 33Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 54Hz (measured, Erin's Audio Corner) |
| Dimensions | 14.6"H x 8.1"W x 12.3"D (370.0 x 205.0 x 312.0 mm) |
| Drivers | 7.1" Magnesium Silicate Polymer woofer, 1.1" Cerotar soft dome with Hexis tweeter |
| Impedance | 6 ohms nominal (5.5 ohms minimum above 80Hz, measured, Erin's Audio Corner) |
| Sensitivity | 83.5dB (measured, Erin's Audio Corner; 86dB manufacturer specified) |
| Spinorama Preference Score | 3.35 |
| Spinorama Preference Score with Perfect Sub | 5.05 |
| Weight | 12.8 lbs (5.8 kg) |
| Woofer Cabinet | ported, rear |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- Dynaudio Emit 20 vs Klipsch RP-600M II
- Dynaudio Emit 20 vs Philharmonic BMR Monitor
- Dynaudio Emit 20 vs JBL Studio 630
- Dynaudio Emit 20 vs Behringer B2030P
- Dynaudio Emit 20 vs Mission LX-3 MKII
- Dynaudio Emit 20 vs Polk Signature Elite ES20
- Dynaudio Emit 20 vs GR-Research X-LS Encore
- Dynaudio Emit 20 vs Infinity IL10
- See all 63 comparisons