Short answer: the MoFi SourcePoint 888 for better sound quality, the Focal Chora 816 for the lower price. The MoFi SourcePoint 888 ranks #4 of 71 floorstanding speakers at $5500. The Focal Chora 816 ranks #14 at $900, $4600 cheaper.
What the Focal Chora 816 offers: CEA2034 spinorama shows a generally even on-axis response with nice bass extension and high sensitivity. Predicted in-room response is very good aside from a peak around 8kHz. Horizontal beamwidth of about ±60 degrees is typical and fairly controlled. Distortion is very low at 86dB SPL/1m and still usable at 96dB SPL/1m. Watch for: Some messiness appears between 500Hz-2kHz on-axis, including a dip around 550Hz. Vertical directivity narrows a little, so listening height matters more than with a coincident design. Cumulative spectral decay (waterfall) shows a fair bit of resonances lingering across the midrange. Distortion rises substantially in the 1-2kHz region at 96dB SPL/1m. Minimum impedance dips to about 3.9 ohms.
What the MoFi SourcePoint 888 offers: Three-way vented design: an 8” coaxial mid-range/1.25” dome tweeter driver plus two additional 8” woofers crossed at about 130Hz, giving genuinely full-range output (F3 34Hz, F10 26Hz) other than the deepest subsonic content. Ranked by the reviewer among his personal top three speakers out of roughly 200 tested, alongside the KEF Blade 2 Meta and Dutch & Dutch 8C, despite costing a small fraction of either. Excellent compression/dynamic-range linearity, holding its own against much pricier speakers like the March Audio Sointuva AWG, KEF Reference 1 Meta, and KEF Blade 2 Meta. On-axis (0°) and 30°-off-axis estimated in-room responses track within about 1-1.5dB of each other above 500Hz, so tonal balance barely changes with placement or listening angle - excellent for multi-seat home theater or entertaining. Wide horizontal dispersion of about ±60°. Distortion stays low: under 1% at 86dB, and under 1% above 200Hz even at 96dB, with multitone distortion mostly under 1% as well. Not a difficult amplifier load (5-ohm minimum impedance, 4.2-ohm minimum EPDR). Checks the three boxes the reviewer considers essential for a home theater speaker: low compression, low distortion, and excellent directivity. Watch for: A significant investment, best ordered from a dealer with a good return policy. Large and heavy floorstander (about 96 lbs, 42” tall) requiring real floor space and rear clearance. Positioning is fairly specific: needs about 2 feet from the rear wall - closer causes boominess in the 40-50Hz region, farther loses bass extension. Vertical dispersion (about ±50°) is narrower than horizontal (about ±60°), since the two 8” woofers are spaced vertically apart on a tower cabinet, causing some vertical mismatch at lower frequencies. A small on-axis dip around 500Hz and a deliberately lower tweeter level (about 0.5dB below the midrange) are intentional design choices for smoother in-room response, but mean the raw on-axis measurement isn’t perfectly flat. A mild diffraction-related dip appears around 3kHz in directivity measurements. Toeing the speaker out more than about 10° starts to noticeably reduce top-end energy.
Buy the Focal Chora 816 if the price matters more than sound quality. Buy the MoFi SourcePoint 888 if sound quality matters more than the price.
Specifications Side By Side
| Focal Chora 816 | MoFi SourcePoint 888 | |
|---|---|---|
| Price | $900 used, Discontinued | $5500 |
| Ranked | #14 of 71 in Large Size Floorstanding Speakers | #4 of 71 in Large Size Floorstanding Speakers |
| Bass Extension (-10dB) | 35Hz (measured, Audio Science Review) | 26Hz (measured, Erin’s Audio Corner) |
| Bass Extension (-3dB) | 60Hz (measured, Audio Science Review) | 34Hz (measured, Erin’s Audio Corner) |
| Dimensions | 40.7"H x 11.8"W x 15.3"D (1033.8 x 299.7 x 388.6 mm) | 41.2"H x 12.6"W x 16.1"D (1046.5 x 320 x 408.9 mm) |
| Impedance | 8 ohms nominal (3.9 ohms minimum, measured, Audio Science Review) | 6 ohms nominal, 5 ohms minimum (measured, Erin’s Audio Corner) |
| Drivers | 6.5" (16.5cm) Slatefiber woofer, 6.5" (16.5cm) Slatefiber midrange, 1" (25mm) TNF Al/Mg inverted dome tweeter | Dual 8" paper cone woofers, 8" Paper Cone midrange, 1.25" wide roll soft dome tweeter |
| Sensitivity | 91dB (measured, Audio Science Review) | 85.6dB (measured, Erin’s Audio Corner) |
| Weight | 40.8 lbs / 18.5 kg each | 94.8 lbs / 43 kg each |
| Discontinued | Yes | - |
| Woofer Cabinet | ported, front | ported, rear |
Related Speaker Comparisons
More useful head-to-heads from the same speaker class:
- KEF R5 Meta vs Revel F208
- KEF Reference 203 vs Klipsch RP-6000F II
- Magnepan LRS+ vs KEF Reference 203
- MoFi SourcePoint 888 vs Revel Concerta2 F35
- Klipsch Forte IV vs Focal Chora 816
Prices on this page were last checked August 25, 2026 at 6:19 AM UTC. Product prices and availability are accurate as of that date/time and are subject to change; the price and availability shown on Amazon at the time of purchase will apply to the purchase of this product.
As an eBay Partner, we may be compensated if you make a purchase.
The Two Speakers In Full
Focal Chora 816: $900 used, Discontinued eBay
Pros: CEA2034 spinorama shows a generally even on-axis response with nice bass extension and high sensitivity. Predicted in-room response is very good aside from a peak around 8kHz. Horizontal beamwidth of about ±60 degrees is typical and fairly controlled. Distortion is very low at 86dB SPL/1m and still usable at 96dB SPL/1m.
Cons: Some messiness appears between 500Hz-2kHz on-axis, including a dip around 550Hz. Vertical directivity narrows a little, so listening height matters more than with a coincident design. Cumulative spectral decay (waterfall) shows a fair bit of resonances lingering across the midrange. Distortion rises substantially in the 1-2kHz region at 96dB SPL/1m. Minimum impedance dips to about 3.9 ohms. Discontinued.
Full Focal Chora 816 review and specifications →
| Bass Extension (-10dB) | 35Hz (measured, Audio Science Review) |
|---|---|
| Bass Extension (-3dB) | 60Hz (measured, Audio Science Review) |
| Dimensions | 40.7"H x 11.8"W x 15.3"D (1033.8 x 299.7 x 388.6 mm) |
| Discontinued | Yes |
| Drivers | 6.5" (16.5cm) Slatefiber woofer, 6.5" (16.5cm) Slatefiber midrange, 1" (25mm) TNF Al/Mg inverted dome tweeter |
| Impedance | 8 ohms nominal (3.9 ohms minimum, measured, Audio Science Review) |
| Sensitivity | 91dB (measured, Audio Science Review) |
| Weight | 40.8 lbs / 18.5 kg each |
| Woofer Cabinet | ported, front |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
MoFi SourcePoint 888: $5500 Crutchfield eBay
Pros: Three-way vented design: an 8” coaxial mid-range/1.25” dome tweeter driver plus two additional 8” woofers crossed at about 130Hz, giving genuinely full-range output (F3 34Hz, F10 26Hz) other than the deepest subsonic content. Ranked by the reviewer among his personal top three speakers out of roughly 200 tested, alongside the KEF Blade 2 Meta and Dutch & Dutch 8C, despite costing a small fraction of either. Excellent compression/dynamic-range linearity, holding its own against much pricier speakers like the March Audio Sointuva AWG, KEF Reference 1 Meta, and KEF Blade 2 Meta. On-axis (0°) and 30°-off-axis estimated in-room responses track within about 1-1.5dB of each other above 500Hz, so tonal balance barely changes with placement or listening angle - excellent for multi-seat home theater or entertaining. Wide horizontal dispersion of about ±60°. Distortion stays low: under 1% at 86dB, and under 1% above 200Hz even at 96dB, with multitone distortion mostly under 1% as well. Not a difficult amplifier load (5-ohm minimum impedance, 4.2-ohm minimum EPDR). Checks the three boxes the reviewer considers essential for a home theater speaker: low compression, low distortion, and excellent directivity.
Cons: A significant investment, best ordered from a dealer with a good return policy. Large and heavy floorstander (about 96 lbs, 42” tall) requiring real floor space and rear clearance. Positioning is fairly specific: needs about 2 feet from the rear wall - closer causes boominess in the 40-50Hz region, farther loses bass extension. Vertical dispersion (about ±50°) is narrower than horizontal (about ±60°), since the two 8” woofers are spaced vertically apart on a tower cabinet, causing some vertical mismatch at lower frequencies. A small on-axis dip around 500Hz and a deliberately lower tweeter level (about 0.5dB below the midrange) are intentional design choices for smoother in-room response, but mean the raw on-axis measurement isn’t perfectly flat. A mild diffraction-related dip appears around 3kHz in directivity measurements. Toeing the speaker out more than about 10° starts to noticeably reduce top-end energy.
Full MoFi SourcePoint 888 review and specifications →
| Bass Extension (-10dB) | 26Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 34Hz (measured, Erin's Audio Corner) |
| Dimensions | 41.2"H x 12.6"W x 16.1"D (1046.5 x 320 x 408.9 mm) |
| Drivers | Dual 8" paper cone woofers, 8" Paper Cone midrange, 1.25" wide roll soft dome tweeter |
| Impedance | 6 ohms nominal, 5 ohms minimum (measured, Erin's Audio Corner) |
| Sensitivity | 85.6dB (measured, Erin's Audio Corner) |
| Weight | 94.8 lbs / 43 kg each |
| Woofer Cabinet | ported, rear |
- Links
- Reviews, Comparisons and Sound Samples
- Erin’s Audio Corner: Why the MoFi SourcePoint 888 Could Be Your Last Speaker Purchase More from Erin’s Audio Corner →
- Erin’s Audio Corner: My Absolute Favorite Products of 2024 Revealed
- Erin’s Audio Corner Website: MoFi SourcePoint 888
- Erin’s Audio Corner Measurements (spinorama.org)
- Reddit Search for MoFi SourcePoint 888 Review
- Head-to-Head Comparisons
- MoFi SourcePoint 888 vs MoFi SourcePoint V10 Master Edition
- MoFi SourcePoint 888 vs KEF Blade Two Meta
- MoFi SourcePoint 888 vs GR-Research NX-Treme
- MoFi SourcePoint 888 vs JBL HDI-3800
- MoFi SourcePoint 888 vs Revel F328Be
- MoFi SourcePoint 888 vs KEF R5 Meta
- MoFi SourcePoint 888 vs KEF R5
- MoFi SourcePoint 888 vs Revel F226Be
- See all 27 comparisons