Short answer: the Polk Audio XT60. It ranks #36 of 59 floorstanding speakers by sound quality at $229; the Dynaudio Emit 30 ranks #46 and costs $1274.25, so there is not much of a tradeoff to weigh.
The case for the Polk Audio XT60: Passive-radiator-loaded design (6.5” woofer plus two 6.5” passive radiators) gives deeper bass than the driver size alone would suggest - 43.9Hz at -3dB / 38.1Hz at -10dB, genuinely competitive extension for a budget tower. The catch: Bass alignment Q is the highest, least-controlled figure in this entire batch, consistent with owner reports of a slightly loose, boomy low end at higher volumes.
On the Dynaudio Emit 30 side: A 2.5-way floorstander: two 5.25” mid-woofers paired with a roughly 1” dome tweeter, driven through dual rear bass-reflex ports. Watch for: A dip and inconsistency in the lower-treble presence region (roughly 2-5kHz) makes the top end sound uneven - sometimes soft, sometimes forward - depending on the specific instrument or frequency being reproduced; male vocals can lack presence and cymbals can lack sizzle as a result.
Buy the Polk Audio XT60. It ranks higher for sound quality than the Dynaudio Emit 30 and costs less, so there is no real case for the other one.
If sound quality matters at all to you, skip the Dynaudio Emit 30. It ranks near the bottom of the 59 floorstanding speakers, so look higher up the list instead.
Specifications Side By Side
| Polk Audio XT60 | Dynaudio Emit 30 | |
|---|---|---|
| Price | $229 | $1,274.25 |
| Ranked | #36 of 59 in Large Size Floorstanding Speakers | #46 of 59 in Large Size Floorstanding Speakers |
| Bass Extension (-10dB) | 38.1Hz (measured, spinorama.org) | 36Hz (measured, Erin’s Audio Corner) |
| Bass Extension (-3dB) | 43.9Hz (measured, spinorama.org) | 44Hz (measured, Erin’s Audio Corner) |
| Impedance | 4/8-ohm compatible | 4 ohms |
| Sensitivity | 86dB (1W/1m) | 87dB |
| Drivers | 1" Terylene dome tweeter, 6.5" bilaminate polypropylene woofer, 2x 6.5" passive radiators | Dual 5.25" mid-woofers, 1" soft dome tweeter |
| Weight | 20 lbs / 9.07 kg (20 lb) each | 34.2 lbs / 15.5 kg |
| Woofer Cabinet | Passive radiator-loaded | ported, rear (dual) |
| Dimensions | 19.05 x 92.5 x 23.09cm (7.5 x 36.4 x 9.09 in) each | 35.4"H x 6.7"W x 10.7"D (900.0 x 170.0 x 272.0 mm) |
| Frequency Response | - | 44Hz - 25kHz (±3dB, manufacturer specified) |
| Power Handling | - | 180W (IEC rated) |
| Country of Origin | - | Denmark |
Related Speaker Comparisons
More useful head-to-heads from the same speaker class:
- Klipsch RP-6000F II vs Polk T50
- Klipsch RP-6000F II vs Infinity Reference 253
- Klipsch RP-6000F II vs Sony SS-CS3
- Dynaudio Emit 30 vs Polk T50
- Polk Audio XT60 vs KEF Q11 Meta
The Two Speakers In Full
Polk Audio XT60: $229 Amazon Bhphotovideo Crutchfield
Pros: Passive-radiator-loaded design (6.5” woofer plus two 6.5” passive radiators) gives deeper bass than the driver size alone would suggest - 43.9Hz at -3dB / 38.1Hz at -10dB, genuinely competitive extension for a budget tower. Hi-Res Audio certified, Dolby Atmos/DTS:X compatible, and works with either 4- or 8-ohm amplifier outputs.
Cons: Bass alignment Q (lfq 0.96) is the highest, least-controlled figure in this entire batch, consistent with owner reports of a slightly loose, boomy low end at higher volumes. On-axis deviation (nbd_on_axis 0.512) is also the roughest measured figure in the batch. The vinyl-wrapped (not wood veneer) cabinet reads as budget up close per owner reviews, and at least one owner reported blowing a driver under sustained heavy bass - some caution is warranted with bass-heavy source material at volume.
Full Polk Audio XT60 review and specifications →
| Bass Extension (-10dB) | 38.1Hz (measured, spinorama.org) |
|---|---|
| Bass Extension (-3dB) | 43.9Hz (measured, spinorama.org) |
| Dimensions | 19.05 x 92.5 x 23.09cm (7.5 x 36.4 x 9.09 in) each |
| Drivers | 1" Terylene dome tweeter, 6.5" bilaminate polypropylene woofer, 2x 6.5" passive radiators |
| Impedance | 4/8-ohm compatible |
| Sensitivity | 86dB (1W/1m) |
| Weight | 20 lbs / 9.07 kg (20 lb) each |
| Woofer Cabinet | Passive radiator-loaded |
As an eBay Partner, we may be compensated if you make a purchase.
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- Polk Audio XT60 vs Klipsch Heresy IV
- Polk Audio XT60 vs Klipsch Forte IV
- Polk Audio XT60 vs Definitive Technology BP-9020
- Polk Audio XT60 vs KEF Q11 Meta
- Polk Audio XT60 vs Klipsch RP-5000F II
- Polk Audio XT60 vs Polk Reserve R500
- Polk Audio XT60 vs ELAC DF63
- Polk Audio XT60 vs PSB Imagine T65
- See all 15 comparisons
Dynaudio Emit 30: $1,274.25 Amazon
Pros: A 2.5-way floorstander: two 5.25” mid-woofers paired with a roughly 1” dome tweeter, driven through dual rear bass-reflex ports. The two woofers hand off at staggered crossover points (around 1kHz and 3.5kHz) rather than sharing one, which avoids the acoustic lobing a shared crossover point would cause between the tweeter and the lower woofer, and adds a few dB of sensitivity in the process. Genuinely deep bass for a speaker around this price - measured F3 near 44Hz and extends audibly down to about 40Hz in-room without much difficulty. Harmonic distortion measures clean and low at both 86dB and 96dB SPL/1m. Good CTA-2034 sound power and uniform directivity mean the speaker takes EQ correction well if a listener wants to dial in its one tonal weak point. Dynamic range and compression performance are strong overall, with only a minor, high-Q compression artifact tied to a cone-edge resonance that’s unlikely to be audible. Wide, consistent horizontal dispersion around ±70° with just a small ~10° narrowing between 1-3kHz, and a reasonably forgiving ±20° vertical window centered on the tweeter axis.
Cons: A dip and inconsistency in the lower-treble presence region (roughly 2-5kHz) makes the top end sound uneven - sometimes soft, sometimes forward - depending on the specific instrument or frequency being reproduced; male vocals can lack presence and cymbals can lack sizzle as a result. A cone-edge surround resonance shows up around 1-1.3kHz in burst-decay measurements (a trait the reviewer has also seen on other Dynaudio models) and lines up with elevated multitone distortion across roughly 600Hz-1.5kHz. An enclosure resonance appears around 350Hz in the impedance curve. Placed too close to a rear wall, the dual ports make the bass noticeably boomy - pulling the speaker out is needed to keep the low end from overloading the room. Fully resolving the top-end inconsistency needs a modest EQ correction (roughly +2dB with a Q of about 1, centered 3-6kHz), so out-of-the-box tonal accuracy in that band isn’t quite class-leading despite otherwise strong measured performance.
Full Dynaudio Emit 30 review and specifications →
| Bass Extension (-10dB) | 36Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 44Hz (measured, Erin's Audio Corner) |
| Country of Origin | Denmark |
| Dimensions | 35.4"H x 6.7"W x 10.7"D (900.0 x 170.0 x 272.0 mm) |
| Drivers | Dual 5.25" mid-woofers, 1" soft dome tweeter |
| Frequency Response | 44Hz - 25kHz (±3dB, manufacturer specified) |
| Impedance | 4 ohms |
| Power Handling | 180W (IEC rated) |
| Sensitivity | 87dB |
| Weight | 34.2 lbs / 15.5 kg |
| Woofer Cabinet | ported, rear (dual) |
As an eBay Partner, we may be compensated if you make a purchase.
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- Dynaudio Emit 30 vs Klipsch RP-6000F II
- Dynaudio Emit 30 vs Klipsch RP-8000F II
- Dynaudio Emit 30 vs Polk T50
- Dynaudio Emit 30 vs Focal Aria Evo X N°2
- Dynaudio Emit 30 vs Sony SS-CS3
- Dynaudio Emit 30 vs SVS Ultra Evolution Pinnacle
- Dynaudio Emit 30 vs Klipsch RP-5000F II
- Dynaudio Emit 30 vs Infinity Reference 253
- See all 17 comparisons