Short answer: the ELAC DBR62 ranks #55 of 130 bookshelf speakers by sound quality at $799; the AsciLab F6Bs ranks #20 at $799. The price gap is small enough that the sound-quality ranking should decide it.
What the ELAC DBR62 offers: Two-way design with a 6.5” woofer and 1” dome tweeter in a shallow waveguide, with the tweeter positioned close to the woofer for near-point-source coherence - giving more vertical listening leeway than typical two-ways. Notably forgiving of placement and aiming: sounds good from directly on-axis all the way to 30° of toe-out (parallel with the rear wall), making it more room-independent than many speakers this price. Wide horizontal radiation of about ±70° until the tweeter starts beaming, right in the reviewer’s preferred sweet spot. A mild, wide-Q bass bump centered around 100Hz adds a bit of extra punch that the reviewer personally likes. On-axis linearity within about ±2.5dB, with a strong measured preference score of 5.3. Distortion stays below 3% at both 86dB and 96dB until around 50Hz. Vertical sweet spot of about ±10-20° works well for multi-row home theater seating. The reviewer calls it “the epitome of a good speaker” for its price, with no reservations recommending it. Watch for: A slight recess in the 1-2kHz region reduces vocal presence somewhat compared to other speakers in direct comparison. A mild hot spot around 4-5kHz can read as slight sibilance when pointed directly on-axis. Low-to-mid sensitivity (about 84.3dB) combined with a current draw that behaves like roughly 2.4 ohms between 100-200Hz means it’s best driven by a dedicated 4-ohm-capable amplifier rather than an AVR. A diffraction dip from the baffle edge is visible in measurements - typical of any standard rectangular-baffle speaker and not correctable without a much more expensive curved-baffle design. Multitone distortion testing suggests some potential midrange distortion could be audible on certain material, though the reviewer didn’t personally notice it. Minor resonances appear around 700Hz and 1-1.5kHz, possibly tied to the enclosure, port, or cone/surround edge termination, though their audible impact appears minimal. F3 of 53Hz means a subwoofer is still needed for real bass extension below about 40Hz.
What the AsciLab F6Bs offers: A slimmer, sealed, VESA 100 wall mountable variant of AsciLab’s F6B, trading the F6B’s passive radiator for a shallower 15.4cm deep cabinet that can go straight on a wall bracket. The sound power directivity index has the tightest standard deviation, 3.32, of anything in this batch of new additions, meaning off axis energy tracks the on axis response unusually consistently for a sealed 2-way this size, and on axis deviation measures a clean 0.25dB average. Watch for: AsciLab’s own site shows the F6Bs sold out, though it remains in stock through resellers like Audiophonics and Tested Audio. Bass extension is measured at 82.0Hz at -3dB, noticeably less than the passive radiator equipped F6B, and listening window smoothness measures only a moderate 0.39. The 4 ohm nominal impedance calls for a reasonably capable amplifier.
Buy the AsciLab F6Bs. It ranks higher for sound quality than the ELAC DBR62 at the same price, so the other one has nothing left to offer.
Still deciding? The full Passive Home rankings cover every ranked option.
Specifications Side By Side
| ELAC DBR62 | AsciLab F6Bs | |
|---|---|---|
| Price | $799.00 per pair | €799 per pair |
| Ranked | #55 of 130 in Large Size Bookshelf Speakers | #20 of 130 in Large Size Bookshelf Speakers |
| Bass Extension (-10dB) | 41Hz (measured, Erin's Audio Corner) | 50.1Hz (measured, Audio Science Review) |
| Bass Extension (-3dB) | 53Hz (measured, Erin's Audio Corner) | 82.0Hz (measured, Audio Science Review) |
| Dimensions | 14.1"H x 8.2"W x 10.8"D (358.1 x 208.3 x 274.3 mm) | 14.5"H x 8"W x 6.1"D (368 x 203 x 154 mm) |
| Impedance | 6 ohms nominal, 5.2 ohms minimum (measured above 80Hz, Erin's Audio Corner) | 4 ohms nominal, 3.7 ohms minimum |
| Sensitivity | 84.3dB (measured average 300Hz-3kHz @ 2.83V/1m, Erin's Audio Corner; 86dB manufacturer specified) | 85.2dB @ 2.83V/1m (measured, Audio Science Review) |
| Drivers | 6.5" Aramid Fiber woofer, 1" soft dome tweeter | 1" aluminum dome tweeter with waveguide and phase plug, 6" fiber cone woofer |
| Weight | 18.1 lbs (8.2 kg) each | 12.3 lbs (5.6 kg) each |
| Woofer Cabinet | ported, front | - |
| Spinorama Preference Score | 4.16 | 4.35 |
| Spinorama Preference Score with Perfect Sub | 6.35 | 7.01 |
| Enclosure | - | sealed |
| Crossover Frequency | - | 1kHz |
| Mounting | - | VESA 100 wall mount compatible |
| Warranty | - | 2 years |
| Country | - | South Korea |
| Maximum SPL | - | 100dB full bandwidth, 102dB above 100Hz (manufacturer specified) |
Related Speaker Comparisons
More top alternatives to AsciLab F6Bs:
- AsciLab F6Bs vs Perlisten S4b
- AsciLab F6Bs vs KEF Reference 1 Meta
- AsciLab F6Bs vs GR-Research NX-Studio
- AsciLab C6B vs AsciLab F6Bs
- Audio First Cadentia 3 vs AsciLab F6Bs
Prices on this page were last checked September 16, 2026 at 12:41 AM UTC. Product prices and availability are accurate as of that date/time and are subject to change; the price and availability shown on Amazon at the time of purchase will apply to the purchase of this product.
As an eBay Partner, we may be compensated if you make a purchase.
The Two Speakers In Full
ELAC DBR62: $799.00 per pair Amazon Crutchfield eBay
Pros: Two-way design with a 6.5” woofer and 1” dome tweeter in a shallow waveguide, with the tweeter positioned close to the woofer for near-point-source coherence - giving more vertical listening leeway than typical two-ways. Notably forgiving of placement and aiming: sounds good from directly on-axis all the way to 30° of toe-out (parallel with the rear wall), making it more room-independent than many speakers this price. Wide horizontal radiation of about ±70° until the tweeter starts beaming, right in the reviewer’s preferred sweet spot. A mild, wide-Q bass bump centered around 100Hz adds a bit of extra punch that the reviewer personally likes. On-axis linearity within about ±2.5dB, with a strong measured preference score of 5.3. Distortion stays below 3% at both 86dB and 96dB until around 50Hz. Vertical sweet spot of about ±10-20° works well for multi-row home theater seating. The reviewer calls it “the epitome of a good speaker” for its price, with no reservations recommending it. Measured bass extension of 53Hz (-3dB), with a measured sensitivity of 84.3dB.
Cons: A slight recess in the 1-2kHz region reduces vocal presence somewhat compared to other speakers in direct comparison. A mild hot spot around 4-5kHz can read as slight sibilance when pointed directly on-axis. Low-to-mid sensitivity (about 84.3dB) combined with a current draw that behaves like roughly 2.4 ohms between 100-200Hz means it’s best driven by a dedicated 4-ohm-capable amplifier rather than an AVR. A diffraction dip from the baffle edge is visible in measurements - typical of any standard rectangular-baffle speaker and not correctable without a much more expensive curved-baffle design. Multitone distortion testing suggests some potential midrange distortion could be audible on certain material, though the reviewer didn’t personally notice it. Minor resonances appear around 700Hz and 1-1.5kHz, possibly tied to the enclosure, port, or cone/surround edge termination, though their audible impact appears minimal. F3 of 53Hz means a subwoofer is still needed for real bass extension below about 40Hz.
Full ELAC DBR62 review and specifications →
| Bass Extension (-10dB) | 41Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 53Hz (measured, Erin's Audio Corner) |
| Dimensions | 14.1"H x 8.2"W x 10.8"D (358.1 x 208.3 x 274.3 mm) |
| Drivers | 6.5" Aramid Fiber woofer, 1" soft dome tweeter |
| Impedance | 6 ohms nominal, 5.2 ohms minimum (measured above 80Hz, Erin's Audio Corner) |
| Sensitivity | 84.3dB (measured average 300Hz-3kHz @ 2.83V/1m, Erin's Audio Corner; 86dB manufacturer specified) |
| Spinorama Preference Score | 4.16 |
| Spinorama Preference Score with Perfect Sub | 6.35 |
| Weight | 18.1 lbs (8.2 kg) each |
| Woofer Cabinet | ported, front |
- Links
- Reviews, Comparisons and Sound Samples
- Erin’s Audio Corner: Top 3 Things You Need to Know About ELAC DBR62 Before You Buy More from Erin’s Audio Corner →
- Erin’s Audio Corner Website Elac DBR62
- Erin’s Audio Corner: 5 AWESOME SPEAKERS Under $1000 You Won’t Regret
- Erin’s Audio Corner: My Top Picks of 2023: Must-Haves Under $3000
- Audio Science Review Measurements More from Audio Science Review →
- Erin’s Audio Corner Measurements (spinorama.org)
- Head-to-Head Comparisons
- ELAC DBR62 vs ELAC Uni-Fi Reference UBR62
- ELAC DBR62 vs Yamaha NS-800A
- ELAC DBR62 vs Definitive Technology Demand D11
- ELAC DBR62 vs Technics SB-C700
- ELAC DBR62 vs Dynaudio Contour 20i
- ELAC DBR62 vs SVS Ultra Bookshelf
- ELAC DBR62 vs Revel Concerta2 M16
- ELAC DBR62 vs Infinity Reference R162
- See all 62 comparisons
AsciLab F6Bs: €799 per pair Audiophonics eBay
Pros: A slimmer, sealed, VESA 100 wall mountable variant of AsciLab’s F6B, trading the F6B’s passive radiator for a shallower 15.4cm deep cabinet that can go straight on a wall bracket. The sound power directivity index has the tightest standard deviation, 3.32, of anything in this batch of new additions, meaning off axis energy tracks the on axis response unusually consistently for a sealed 2-way this size, and on axis deviation measures a clean 0.25dB average. Measured bass extension of 82.0Hz (-3dB), with a measured sensitivity of 85.2dB.
Cons: AsciLab’s own site shows the F6Bs sold out, though it remains in stock through resellers like Audiophonics and Tested Audio. Bass extension is measured at 82.0Hz at -3dB, noticeably less than the passive radiator equipped F6B, and listening window smoothness measures only a moderate 0.39. The 4 ohm nominal impedance calls for a reasonably capable amplifier.
Full AsciLab F6Bs review and specifications →
| Bass Extension (-10dB) | 50.1Hz (measured, Audio Science Review) |
|---|---|
| Bass Extension (-3dB) | 82.0Hz (measured, Audio Science Review) |
| Country | South Korea |
| Crossover Frequency | 1kHz |
| Dimensions | 14.5"H x 8"W x 6.1"D (368 x 203 x 154 mm) |
| Drivers | 1" aluminum dome tweeter with waveguide and phase plug, 6" fiber cone woofer |
| Enclosure | sealed |
| Impedance | 4 ohms nominal, 3.7 ohms minimum |
| Maximum SPL | 100dB full bandwidth, 102dB above 100Hz (manufacturer specified) |
| Mounting | VESA 100 wall mount compatible |
| Sensitivity | 85.2dB @ 2.83V/1m (measured, Audio Science Review) |
| Spinorama Preference Score | 4.35 |
| Spinorama Preference Score with Perfect Sub | 7.01 |
| Warranty | 2 years |
| Weight | 12.3 lbs (5.6 kg) each |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- AsciLab F6Bs vs Epos ES14N
- AsciLab F6Bs vs Arendal 1528 Monitor 8
- AsciLab F6Bs vs MoFi SourcePoint 8
- AsciLab F6Bs vs Ascend Acoustics CMT-340 SE2
- AsciLab F6Bs vs Wharfedale Super Linton
- AsciLab F6Bs vs Buchardt Audio E50
- AsciLab F6Bs vs KEF R3
- AsciLab F6Bs vs MoFi SourcePoint 10
- See all 45 comparisons