Short answer: the Dynaudio Emit 30. It ranks #139 of 226 floorstanding speakers by sound quality, rated 3.9/5, at $1,274.25; the Klipsch RP-8060FA II ranks #164, rated 3.8/5, and costs $2,599.98, so there is little reason to consider the other one.
What the Dynaudio Emit 30 does well: A 2.5-way floorstander: two 5.25” mid-woofers paired with a roughly 1” dome tweeter, driven through dual rear bass-reflex ports. The catch: A dip and inconsistency in the lower-treble presence region (roughly 2-5kHz) makes the top end sound uneven (sometimes soft, sometimes forward) depending on the specific instrument or frequency being reproduced; male vocals can lack presence and cymbals can lack sizzle as a result.
The case for the Klipsch RP-8060FA II: The Klipsch RP-8000F II with a built-in Dolby Atmos up-firing module: two 8” Cerametallic woofers and a horn loaded titanium tweeter, rated from 35Hz at 98dB. The tradeoff: No independent measurements yet, so its tonal balance and directivity can’t be compared with ranked speakers.
Buy the Dynaudio Emit 30. It is rated higher for sound quality than the Klipsch RP-8060FA II and costs less, so only choose the other one for a particular feature it does better.
About the ratings: the Klipsch RP-8060FA II’s rating is estimated from measured siblings and predecessors rather than its own measurements, with a likely range of 3.5 to 4.1, so this verdict could change once it is measured.
Still deciding? The full Passive Home rankings cover every ranked option.
Specifications Side By Side
| Dynaudio Emit 30 | Klipsch RP-8060FA II | |
|---|---|---|
| Price | $1,274.25 per pair | $2,599.98 per pair |
| Ranked | #139 of 226 in Large Size Floorstanding Speakers | #164 of 226 in Large Size Floorstanding Speakers Estimated |
| Bass Extension (-10dB) | 36Hz (measured, Erin’s Audio Corner) | - |
| Bass Extension (-3dB) | 44Hz (measured, Erin’s Audio Corner) | 35Hz (manufacturer specified) |
| Drivers | Dual 5.25” mid-woofers, 1” soft dome tweeter | 1x 1” titanium LTS tweeter on hybrid Tractrix horn, 2x 8” Cerametallic woofers, plus 1x 6.5” up-firing Atmos woofer and 1” tweeter |
| Weight | 34.2 lbs (15.5 kg) | 75.6 lbs (34.3 kg) |
| Sensitivity | 87dB | 98dB (manufacturer specified) |
| Impedance | 4 ohms | 8 ohms nominal (manufacturer specified) |
| Dimensions | 35.4”H x 6.7”W x 10.7”D (900.0 x 170.0 x 272.0 mm) | 43.1”H x 10.9”W x 20.8”D (1095 x 276 x 529 mm) |
| Woofer Cabinet | ported, rear (dual) | - |
| Frequency Response | 44Hz - 25kHz (±3dB, manufacturer specified) | 35Hz - 25kHz (±3dB, manufacturer specified) |
| Power Handling | 180W (IEC rated) | - |
| Country | Denmark | - |
| Spinorama Preference Score | 3.84 | - |
| Spinorama Preference Score with Perfect Sub | 5.69 | - |
| DIY Kit | No | - |
| Amplifier Power | - | 150W RMS continuous (600W peak) |
| Enclosure | - | Bass reflex, MDF, Dolby Atmos enabled |
Related Speaker Comparisons
More worthwhile head-to-heads for Dynaudio Emit 30:
- Dynaudio Emit 30 vs KEF Blade Two Meta
- MoFi SourcePoint V10 Master Edition vs Dynaudio Emit 30
- Dynaudio Emit 30 vs MoFi SourcePoint 888
- Dynaudio Emit 30 vs Revel F328Be
- Radiant Acoustics Clarity 66 vs Dynaudio Emit 30
Prices on this page were last checked October 11, 2026 at 4:59 PM UTC. Product prices and availability are accurate as of that date/time and are subject to change; the price and availability shown on Amazon at the time of purchase will apply to the purchase of this product.
As an eBay Partner, we may be compensated if you make a purchase.
The Two Speakers In Full
Dynaudio Emit 30: $1,274.25 per pair Amazon eBay
Same family: the Dynaudio Emit 10 (smaller bookshelf, estimated 3.2/5), the Dynaudio Emit 20 (larger bookshelf, rated 3.6/5), the Dynaudio Emit 50 (larger floorstanding, ranked higher, estimated 4.2/5) and the Dynaudio Emit 25C (center, estimated 3.7/5). See every Dynaudio Emit generation.
Pros: A 2.5-way floorstander: two 5.25” mid-woofers paired with a roughly 1” dome tweeter, driven through dual rear bass-reflex ports. The two woofers hand off at staggered crossover points (around 1kHz and 3.5kHz) rather than sharing one, which avoids the acoustic lobing a shared crossover point would cause between the tweeter and the lower woofer, and adds a few dB of sensitivity in the process. Genuinely deep bass for a speaker around this price: measured F3 near 44Hz and extends audibly down to about 40Hz in-room without much difficulty. Harmonic distortion measures clean and low at both 86dB and 96dB SPL/1m. Good CTA-2034 sound power and uniform directivity mean the speaker takes EQ correction well if a listener wants to dial in its one tonal weak point. Dynamic range and compression performance are strong overall, with only a minor, high-Q compression artifact tied to a cone-edge resonance that’s unlikely to be audible. Wide, consistent horizontal dispersion around ±70° with just a small ~10° narrowing between 1-3kHz, and a reasonably forgiving ±20° vertical window centered on the tweeter axis. Measured bass extension of 44Hz (-3dB).
Cons: A dip and inconsistency in the lower-treble presence region (roughly 2-5kHz) makes the top end sound uneven (sometimes soft, sometimes forward) depending on the specific instrument or frequency being reproduced; male vocals can lack presence and cymbals can lack sizzle as a result. A cone-edge surround resonance shows up around 1-1.3kHz in burst-decay measurements (a trait the reviewer has also seen on other Dynaudio models) and lines up with elevated multitone distortion across roughly 600Hz-1.5kHz. An enclosure resonance appears around 350Hz in the impedance curve. Placed too close to a rear wall, the dual ports make the bass noticeably boomy: pulling the speaker out is needed to keep the low end from overloading the room. Fully resolving the top-end inconsistency needs a modest EQ correction (roughly +2dB with a Q of about 1, centered 3-6kHz), so out-of-the-box tonal accuracy in that band isn’t quite class-leading despite otherwise strong measured performance.
Full Dynaudio Emit 30 review and specifications →
| Released | Jun 2021 (5 years ago) |
|---|---|
| Bass Extension (-10dB) | 36Hz (measured, Erin’s Audio Corner) |
| Bass Extension (-3dB) | 44Hz (measured, Erin’s Audio Corner) |
| Country | Denmark |
| DIY Kit | No |
| Dimensions | 35.4”H x 6.7”W x 10.7”D (900.0 x 170.0 x 272.0 mm) |
| Drivers | Dual 5.25” mid-woofers, 1” soft dome tweeter |
| Frequency Response | 44Hz - 25kHz (±3dB, manufacturer specified) |
| Impedance | 4 ohms |
| Power Handling | 180W (IEC rated) |
| Sensitivity | 87dB |
| Spinorama Preference Score | 3.84 |
| Spinorama Preference Score with Perfect Sub | 5.69 |
| Weight | 34.2 lbs (15.5 kg) |
| Woofer Cabinet | ported, rear (dual) |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- Dynaudio Emit 30 vs Klipsch RP-6000F II
- Dynaudio Emit 30 vs Klipsch RP-8000F II
- Dynaudio Emit 30 vs PSB Alpha T20
- Dynaudio Emit 30 vs MartinLogan Motion F20
- Dynaudio Emit 30 vs Definitive Technology BP-9020
- Dynaudio Emit 30 vs SVS Ultra Evolution Pinnacle
- Dynaudio Emit 30 vs Polk T50
- Dynaudio Emit 30 vs Klipsch RP-5000F II
- See all 49 comparisons
Klipsch RP-8060FA II: $2,599.98 per pair Estimated Amazon eBay
Same family: the Klipsch RP-500M II (smaller bookshelf, rated 4/5), the Klipsch RP-600M II (larger bookshelf, rated 3.7/5), the Klipsch RP-5000F II (smaller floorstanding, ranked higher, rated 4/5), the Klipsch RP-6000F II (smaller floorstanding, ranked higher, rated 3.9/5), the Klipsch RP-8000F II (smaller floorstanding, ranked higher, rated 3.9/5), the Klipsch RP-404C II (smallest center, rated 3.7/5), the Klipsch RP-500C II (center, rated 3.9/5), the Klipsch RP-504C II (largest center, rated 3.8/5), the Klipsch Reference Premiere RP-500SA II (smaller surround, estimated 3.5/5) and the Klipsch Reference Premiere RP-502S II (larger surround, estimated 3.5/5). See every Klipsch Reference Premiere generation.
Pros: The Klipsch RP-8000F II with a built-in Dolby Atmos up-firing module: two 8” Cerametallic woofers and a horn loaded titanium tweeter, rated from 35Hz at 98dB.
Cons: No independent measurements yet, so its tonal balance and directivity can’t be compared with ranked speakers. The horn tweeter can sound forward in bright rooms, and at 34.3 kg each it is heavy.
Full Klipsch RP-8060FA II review and specifications →
| Released | 2022 (4 years ago) |
|---|---|
| Amplifier Power | 150W RMS continuous (600W peak) |
| Bass Extension (-3dB) | 35Hz (manufacturer specified) |
| Dimensions | 43.1”H x 10.9”W x 20.8”D (1095 x 276 x 529 mm) |
| Drivers | 1x 1” titanium LTS tweeter on hybrid Tractrix horn, 2x 8” Cerametallic woofers, plus 1x 6.5” up-firing Atmos woofer and 1” tweeter |
| Enclosure | Bass reflex, MDF, Dolby Atmos enabled |
| Frequency Response | 35Hz - 25kHz (±3dB, manufacturer specified) |
| Impedance | 8 ohms nominal (manufacturer specified) |
| Sensitivity | 98dB (manufacturer specified) |
| Weight | 75.6 lbs (34.3 kg) |
- Links
- Reviews, Comparisons and Sound Samples
- No independent measurement review is linked for this model; it is ranked from hands-on listening and comparison against similarly priced speakers.
- Head-to-Head Comparisons