Short answer: the Ascend Sierra 1 v2 for better sound quality, the JBL Control 1 Pro for the lower price. The Ascend Sierra 1 v2 ranks #3 of 74 bookshelf speakers at $1000. The JBL Control 1 Pro ranks #64 at $164, $836 cheaper.
What the Ascend Sierra 1 v2 offers: Formaldehyde-free layered bamboo ply cabinet with a 1” dome tweeter over a 5.25” midwoofer, mated by a 4th-order acoustic crossover rather than a stock textbook design. In-room response is extremely linear - the reviewer called it “textbook” - a clear step up from the earlier V1, which had boxiness around 700Hz-1kHz and sibilance around 4-6kHz. Preference score of 8.4 with a subwoofer (6.8 without), which the reviewer calls topnotch. Wide, even horizontal radiation of about ±70° up to 6kHz. Better vertical directivity than its tweeter-to-woofer spacing would suggest, thanks to the steep 4th-order crossover slopes. No mechanical noise, port chuffing, or woofer bottoming even driven to 96dB/1m. In a three-way comparison against the Dynaudio Emit 20 and a Revel bookshelf model (all around $1,000/pair), measured as the most linear of the three and was the reviewer’s personal pick over both, despite the Dynaudio’s deeper bass and higher output capability. Independent ASR Klippel measurements corroborate Erin’s findings: superb off-axis response with only slight on-axis variations, and an in-room response the reviewer called “incredibly smooth and accurate - amazing for a non-DSP speaker.” Distortion above 200Hz at 86dB/1m is very low for the class. Watch for: F3 of 55Hz and F10 of 39Hz mean in-room extension tops out in the mid-40s Hz; the reviewer still recommends a subwoofer for full-range material. Diffraction dips appear around 3kHz and 5-6kHz, and the 1” dome tweeter starts beaming above roughly 6.7kHz, narrowing the soundstage radiation in the top octave - a straightforward consequence of dome size rather than a design flaw. At 96dB/1m the 5.25” midwoofer shows increased distortion in the midrange, likely tied to motor topology; high-passing to a subwoofer around 80Hz largely clears it up. Moderate sensitivity (~81-82dB average) with a 7-ohm minimum impedance. ASR’s power-sweep testing found response holds steady up to 96dB SPL/1m, but pushing to 102dB causes midbass below 400Hz to sag with distortion “through the roof” - a harder output ceiling than the 96dB tests alone suggest. Vertical directivity also narrows above about 1kHz, so the reviewer recommends staying at tweeter-axis height for best results.
What the JBL Control 1 Pro offers: Magnetically shielded transducers and a rugged molded enclosure make it a durable choice for wall-mount or install use, with SonicGuard overload protection built into the crossover. Feels solidly built despite the low price, and the professional crossover network uses steep slopes. Watch for: Sound power and predicted in-room response measurements are badly uneven compared to the JBL 305P Mark II tested alongside it, with no waveguide to control directivity as the woofer beams before handing off to the tweeter. The reviewer performed no distortion or dedicated listening test on this unit and concluded he didn’t “think there is a reason to purchase it” over a proper studio monitor at a similar price.
Buy the Ascend Sierra 1 v2 if sound quality matters more than the price. Buy the JBL Control 1 Pro if the price matters more than sound quality.
If sound quality matters at all to you, skip the JBL Control 1 Pro. It ranks near the bottom of the 74 bookshelf speakers, so look higher up the list instead.
Specifications Side By Side
| Ascend Sierra 1 v2 | JBL Control 1 Pro | |
|---|---|---|
| Price | $1000 | $164 |
| Ranked | #3 of 74 in Medium Size Bookshelf Speakers | #64 of 74 in Medium Size Bookshelf Speakers |
| Bass Extension (-10dB) | 39Hz (measured, Erin’s Audio Corner) | 55Hz (measured, Audio Science Review) |
| Bass Extension (-3dB) | 55Hz (measured, Erin’s Audio Corner) | 78Hz (measured, Audio Science Review) |
| Dimensions | 14.2"H x 7.5"W x 10.5"D (361.9 x 190.5 x 266.7 mm) | 9.3H x 6.3W x 5.6D in |
| Impedance | 8 ohms nominal, 7 ohms minimum (measured, Erin’s Audio Corner) | 4 ohms |
| Sensitivity | 81.5dB (measured, Erin’s Audio Corner) | 87dB (2.83V/1m, measured, Audio Science Review) |
| Drivers | 5.25" proprietary mineral-filled polypropylene cone with cast aluminum frame woofer, 26mm aluminum/magnesium alloy dome tweeter with titanium former (SEAS Titan) | 5.25" low frequency driver, 0.75" polycarbonate dome tweeter |
| Weight | 18.5 lbs / 8.4 kg each | 4 lbs / 1.8 kg each |
| Woofer Cabinet | ported | sealed |
| Frequency Response | - | 80Hz - 20kHz -10dB (Manufacturer specified) |
| Power Handling | - | 150W |
Related Speaker Comparisons
More useful head-to-heads from the same speaker class:
- JBL L52 Classic vs Polk T15
- JBL L52 Classic vs Fluance Signature HFS
- Q Acoustics 5020 vs Polk T15
- Pioneer SP-BS22-LR (Philharmonic AAM Mod) vs Ascend Sierra 1 v2
- Ascend Sierra 1 v2 vs Micca RB42
Prices on this page were last checked August 24, 2026 at 6:53 AM UTC. Product prices and availability are accurate as of that date/time and are subject to change; the price and availability shown on Amazon at the time of purchase will apply to the purchase of this product.
As an eBay Partner, we may be compensated if you make a purchase.
The Two Speakers In Full
Ascend Sierra 1 v2: $1000 Ascendacoustics eBay
Pros: Formaldehyde-free layered bamboo ply cabinet with a 1” dome tweeter over a 5.25” midwoofer, mated by a 4th-order acoustic crossover rather than a stock textbook design. In-room response is extremely linear - the reviewer called it “textbook” - a clear step up from the earlier V1, which had boxiness around 700Hz-1kHz and sibilance around 4-6kHz. Preference score of 8.4 with a subwoofer (6.8 without), which the reviewer calls topnotch. Wide, even horizontal radiation of about ±70° up to 6kHz. Better vertical directivity than its tweeter-to-woofer spacing would suggest, thanks to the steep 4th-order crossover slopes. No mechanical noise, port chuffing, or woofer bottoming even driven to 96dB/1m. In a three-way comparison against the Dynaudio Emit 20 and a Revel bookshelf model (all around $1,000/pair), measured as the most linear of the three and was the reviewer’s personal pick over both, despite the Dynaudio’s deeper bass and higher output capability. Independent ASR Klippel measurements corroborate Erin’s findings: superb off-axis response with only slight on-axis variations, and an in-room response the reviewer called “incredibly smooth and accurate - amazing for a non-DSP speaker.” Distortion above 200Hz at 86dB/1m is very low for the class.
Cons: F3 of 55Hz and F10 of 39Hz mean in-room extension tops out in the mid-40s Hz; the reviewer still recommends a subwoofer for full-range material. Diffraction dips appear around 3kHz and 5-6kHz, and the 1” dome tweeter starts beaming above roughly 6.7kHz, narrowing the soundstage radiation in the top octave - a straightforward consequence of dome size rather than a design flaw. At 96dB/1m the 5.25” midwoofer shows increased distortion in the midrange, likely tied to motor topology; high-passing to a subwoofer around 80Hz largely clears it up. Moderate sensitivity (~81-82dB average) with a 7-ohm minimum impedance. ASR’s power-sweep testing found response holds steady up to 96dB SPL/1m, but pushing to 102dB causes midbass below 400Hz to sag with distortion “through the roof” - a harder output ceiling than the 96dB tests alone suggest. Vertical directivity also narrows above about 1kHz, so the reviewer recommends staying at tweeter-axis height for best results.
Full Ascend Sierra 1 v2 review and specifications →
| Bass Extension (-10dB) | 39Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 55Hz (measured, Erin's Audio Corner) |
| Dimensions | 14.2"H x 7.5"W x 10.5"D (361.9 x 190.5 x 266.7 mm) |
| Drivers | 5.25" proprietary mineral-filled polypropylene cone with cast aluminum frame woofer, 26mm aluminum/magnesium alloy dome tweeter with titanium former (SEAS Titan) |
| Impedance | 8 ohms nominal, 7 ohms minimum (measured, Erin's Audio Corner) |
| Sensitivity | 81.5dB (measured, Erin's Audio Corner) |
| Weight | 18.5 lbs / 8.4 kg each |
| Woofer Cabinet | ported |
- Links
- Reviews, Comparisons and Sound Samples
- Erin’s Audio Corner: NEW! Ascend Acoustics Sierra-1 V2 Review More from Erin’s Audio Corner →
- Erin’s Audio Corner Website Ascend Sierra 1 v2
- Audio Science Review Ascend Sierra 1 v2 More from Audio Science Review →
- Erin’s Audio Corner: 5 AWESOME SPEAKERS Under $1000 You Won’t Regret
- Erin’s Audio Corner: I Tested 250 Speakers So You Don’t Have To!
- Erin’s Audio Corner: My Top Picks of 2023: Must-Haves Under $3000
- Manufacturer Measurements (spinorama.org)
- Reddit Search for Ascend Sierra 1 v2 Review
- Head-to-Head Comparisons
- Ascend Sierra 1 v2 vs KEF LS50 Meta
- Ascend Sierra 1 v2 vs Philharmonic Ceramic Mini
- Ascend Sierra 1 v2 vs Audio First Fidelia
- Ascend Sierra 1 v2 vs Arendal 1961 Monitor
- Ascend Sierra 1 v2 vs Moondrop M4P MTM
- Ascend Sierra 1 v2 vs Emotiva B1+
- Ascend Sierra 1 v2 vs Klipsch RP-500M II
- Ascend Sierra 1 v2 vs Wharfedale Super Denton
- See all 36 comparisons
JBL Control 1 Pro: $164 Parts Express eBay
Pros: Magnetically shielded transducers and a rugged molded enclosure make it a durable choice for wall-mount or install use, with SonicGuard overload protection built into the crossover. Feels solidly built despite the low price, and the professional crossover network uses steep slopes.
Cons: Sound power and predicted in-room response measurements are badly uneven compared to the JBL 305P Mark II tested alongside it, with no waveguide to control directivity as the woofer beams before handing off to the tweeter. The reviewer performed no distortion or dedicated listening test on this unit and concluded he didn’t “think there is a reason to purchase it” over a proper studio monitor at a similar price.
Full JBL Control 1 Pro review and specifications →
| Bass Extension (-10dB) | 55Hz (measured, Audio Science Review) |
|---|---|
| Bass Extension (-3dB) | 78Hz (measured, Audio Science Review) |
| Dimensions | 9.3H x 6.3W x 5.6D in |
| Drivers | 5.25" low frequency driver, 0.75" polycarbonate dome tweeter |
| Frequency Response | 80Hz - 20kHz -10dB (Manufacturer specified) |
| Impedance | 4 ohms |
| Power Handling | 150W |
| Sensitivity | 87dB (2.83V/1m, measured, Audio Science Review) |
| Weight | 4 lbs / 1.8 kg each |
| Woofer Cabinet | sealed |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- JBL Control 1 Pro vs Polk T15
- JBL Control 1 Pro vs Fluance Signature HFS
- JBL Control 1 Pro vs Definitive Technology ProMonitor 1000
- JBL Control 1 Pro vs JBL Stage A130
- JBL Control 1 Pro vs Q Acoustics 5020
- JBL Control 1 Pro vs Micca RB42
- JBL Control 1 Pro vs Pioneer Elite SP-EBS73-LR
- JBL Control 1 Pro vs Q Acoustics 3020i
- See all 26 comparisons