Short answer: the AsciLab F6Bs on measured sound quality, the Polk R200 on price. The AsciLab F6Bs ranks #20 of 130 bookshelf speakers at $799. The Polk R200 ranks #98 at $719, $80 cheaper.
What the Polk R200 offers: Two-way design with a 6.5” midwoofer and 1” ring radiator tweeter, giving reasonably tight, well-defined imaging. Neutral through most of the midrange (roughly 200Hz-1kHz). On-axis response holds within about 1.5dB up to 10kHz. About 20dB of usable dynamic range (76dB to 96dB) before more significant compression sets in. Reasonably close to a 4-ohm nominal load, giving some flexibility with amplifier choice, though a dedicated 4-ohm-capable amp is still recommended. Watch for: A resonance and associated distortion increase around 800Hz-1kHz creates a “tinny,” occasionally glaring quality on certain instruments and vocals, confirmed both by ear and in the frequency-response and distortion measurements. Above about 10kHz, the ring-radiator tweeter takes on an artificial, “digital-esque” quality, then falls off quickly above 16kHz. F3 of 74Hz and F10 of 50Hz mean there’s essentially no meaningful bass “thump” below about 60Hz - a subwoofer is strongly recommended even just to restore basic kick-drum presence. The ring radiator tweeter’s dispersion narrows sharply above about 8kHz, so the speaker should be aimed close to on-axis (no more than 5-10° of toe-out). Vertical listening position is fairly critical - moving more than a few degrees above or below the tweeter line causes a noticeable timbre shift due to a gap in the crossover region. Multitone distortion spikes substantially (to around 10%) in the 600Hz-1kHz region at higher output levels (around 96dB/1m), meaning the glare gets worse the louder it’s played. At the highest tested output (102dB, 26dB of dynamic range), the woofer shows clear signs of struggling; crossing to a subwoofer around 80-100Hz helps prevent bottoming out but doesn’t fully eliminate the compression.
What the AsciLab F6Bs offers: A slimmer, sealed, VESA 100 wall mountable variant of AsciLab’s F6B, trading the F6B’s passive radiator for a shallower 15.4cm deep cabinet that can go straight on a wall bracket. The sound power directivity index has the tightest standard deviation, 3.32, of anything in this batch of new additions, meaning off axis energy tracks the on axis response unusually consistently for a sealed 2-way this size, and on axis deviation measures a clean 0.25dB average. Watch for: AsciLab’s own site shows the F6Bs sold out, though it remains in stock through resellers like Audiophonics and Tested Audio. Bass extension is measured at 82.0Hz at -3dB, noticeably less than the passive radiator equipped F6B, and listening window smoothness measures only a moderate 0.39. The 4 ohm nominal impedance calls for a reasonably capable amplifier.
Buy the Polk R200 if the price matters more than sound quality. Buy the AsciLab F6Bs if sound quality matters more than the price.
If sound quality matters at all to you, skip the Polk R200. It ranks near the bottom of the 130 bookshelf speakers, so look higher up the list instead.
Looking for alternatives? See the complete Passive Home rankings.
Specifications Side By Side
| Polk R200 | AsciLab F6Bs | |
|---|---|---|
| Price | $719.00 per pair | €799 per pair |
| Ranked | #98 of 130 in Large Size Bookshelf Speakers | #20 of 130 in Large Size Bookshelf Speakers |
| Bass Extension (-10dB) | 50Hz (measured, Erin's Audio Corner) | 50.1Hz (measured, Audio Science Review) |
| Bass Extension (-3dB) | 74Hz (measured, Erin's Audio Corner) | 82.0Hz (measured, Audio Science Review) |
| Impedance | 4 ohms nominal, 3.8 ohms minimum (measured, Erin's Audio Corner) | 4 ohms nominal, 3.7 ohms minimum |
| Sensitivity | 85dB | 85.2dB @ 2.83V/1m (measured, Audio Science Review) |
| Drivers | 25mm soft dome + 165mm woofer | 1" aluminum dome tweeter with waveguide and phase plug, 6" fiber cone woofer |
| Weight | 31.3 lbs (14.2 kg) | 12.3 lbs (5.6 kg) each |
| Dimensions | 14.1"H x 7.5"W x 13.9"D (359.0 x 190.0 x 353.8 mm) | 14.5"H x 8"W x 6.1"D (368 x 203 x 154 mm) |
| Woofer Cabinet | ported, rear | - |
| Spinorama Preference Score | 4.34 | 4.35 |
| Spinorama Preference Score with Perfect Sub | 6.86 | 7.01 |
| Enclosure | - | sealed |
| Crossover Frequency | - | 1kHz |
| Mounting | - | VESA 100 wall mount compatible |
| Warranty | - | 2 years |
| Country | - | South Korea |
| Maximum SPL | - | 100dB full bandwidth, 102dB above 100Hz (manufacturer specified) |
Related Speaker Comparisons
How AsciLab F6Bs compares with other leading options:
- AsciLab F6Bs vs Perlisten S4b
- AsciLab F6Bs vs KEF Reference 1 Meta
- AsciLab F6Bs vs GR-Research NX-Studio
- AsciLab C6B vs AsciLab F6Bs
- Audio First Cadentia 3 vs AsciLab F6Bs
Prices on this page were last checked September 16, 2026 at 12:41 AM UTC. Product prices and availability are accurate as of that date/time and are subject to change; the price and availability shown on Amazon at the time of purchase will apply to the purchase of this product.
As an eBay Partner, we may be compensated if you make a purchase.
The Two Speakers In Full
Polk R200: $719.00 per pair Amazon eBay
Pros: Two-way design with a 6.5” midwoofer and 1” ring radiator tweeter, giving reasonably tight, well-defined imaging. Neutral through most of the midrange (roughly 200Hz-1kHz). On-axis response holds within about 1.5dB up to 10kHz. About 20dB of usable dynamic range (76dB to 96dB) before more significant compression sets in. Reasonably close to a 4-ohm nominal load, giving some flexibility with amplifier choice, though a dedicated 4-ohm-capable amp is still recommended. Measured bass extension of 74Hz (-3dB).
Cons: A resonance and associated distortion increase around 800Hz-1kHz creates a “tinny,” occasionally glaring quality on certain instruments and vocals, confirmed both by ear and in the frequency-response and distortion measurements. Above about 10kHz, the ring-radiator tweeter takes on an artificial, “digital-esque” quality, then falls off quickly above 16kHz. F3 of 74Hz and F10 of 50Hz mean there’s essentially no meaningful bass “thump” below about 60Hz - a subwoofer is strongly recommended even just to restore basic kick-drum presence. The ring radiator tweeter’s dispersion narrows sharply above about 8kHz, so the speaker should be aimed close to on-axis (no more than 5-10° of toe-out). Vertical listening position is fairly critical - moving more than a few degrees above or below the tweeter line causes a noticeable timbre shift due to a gap in the crossover region. Multitone distortion spikes substantially (to around 10%) in the 600Hz-1kHz region at higher output levels (around 96dB/1m), meaning the glare gets worse the louder it’s played. At the highest tested output (102dB, 26dB of dynamic range), the woofer shows clear signs of struggling; crossing to a subwoofer around 80-100Hz helps prevent bottoming out but doesn’t fully eliminate the compression.
Full Polk R200 review and specifications →
| Bass Extension (-10dB) | 50Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 74Hz (measured, Erin's Audio Corner) |
| Dimensions | 14.1"H x 7.5"W x 13.9"D (359.0 x 190.0 x 353.8 mm) |
| Drivers | 25mm soft dome + 165mm woofer |
| Impedance | 4 ohms nominal, 3.8 ohms minimum (measured, Erin's Audio Corner) |
| Sensitivity | 85dB |
| Spinorama Preference Score | 4.34 |
| Spinorama Preference Score with Perfect Sub | 6.86 |
| Weight | 31.3 lbs (14.2 kg) |
| Woofer Cabinet | ported, rear |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
AsciLab F6Bs: €799 per pair Audiophonics eBay
Pros: A slimmer, sealed, VESA 100 wall mountable variant of AsciLab’s F6B, trading the F6B’s passive radiator for a shallower 15.4cm deep cabinet that can go straight on a wall bracket. The sound power directivity index has the tightest standard deviation, 3.32, of anything in this batch of new additions, meaning off axis energy tracks the on axis response unusually consistently for a sealed 2-way this size, and on axis deviation measures a clean 0.25dB average. Measured bass extension of 82.0Hz (-3dB), with a measured sensitivity of 85.2dB.
Cons: AsciLab’s own site shows the F6Bs sold out, though it remains in stock through resellers like Audiophonics and Tested Audio. Bass extension is measured at 82.0Hz at -3dB, noticeably less than the passive radiator equipped F6B, and listening window smoothness measures only a moderate 0.39. The 4 ohm nominal impedance calls for a reasonably capable amplifier.
Full AsciLab F6Bs review and specifications →
| Bass Extension (-10dB) | 50.1Hz (measured, Audio Science Review) |
|---|---|
| Bass Extension (-3dB) | 82.0Hz (measured, Audio Science Review) |
| Country | South Korea |
| Crossover Frequency | 1kHz |
| Dimensions | 14.5"H x 8"W x 6.1"D (368 x 203 x 154 mm) |
| Drivers | 1" aluminum dome tweeter with waveguide and phase plug, 6" fiber cone woofer |
| Enclosure | sealed |
| Impedance | 4 ohms nominal, 3.7 ohms minimum |
| Maximum SPL | 100dB full bandwidth, 102dB above 100Hz (manufacturer specified) |
| Mounting | VESA 100 wall mount compatible |
| Sensitivity | 85.2dB @ 2.83V/1m (measured, Audio Science Review) |
| Spinorama Preference Score | 4.35 |
| Spinorama Preference Score with Perfect Sub | 7.01 |
| Warranty | 2 years |
| Weight | 12.3 lbs (5.6 kg) each |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- AsciLab F6Bs vs Epos ES14N
- AsciLab F6Bs vs Arendal 1528 Monitor 8
- AsciLab F6Bs vs MoFi SourcePoint 8
- AsciLab F6Bs vs Ascend Acoustics CMT-340 SE2
- AsciLab F6Bs vs Wharfedale Super Linton
- AsciLab F6Bs vs Buchardt Audio E50
- AsciLab F6Bs vs KEF R3
- AsciLab F6Bs vs MoFi SourcePoint 10
- See all 45 comparisons