Short answer: the KEF R11 Meta for better sound quality, the Dynaudio Emit 30 for the lower price. The KEF R11 Meta ranks #26 of 68 floorstanding speakers at $3499.99. The Dynaudio Emit 30 ranks #53 at $1274.25, $2225.74 cheaper.
What the KEF R11 Meta offers: CEA2034 spinorama shows a generally flat on-axis response with good directivity and very deep bass extension (F10 of 30Hz). Predicted in-room response is very smooth aside from the small 1-1.5kHz dip. The coaxial Uni-Q driver gives excellent, symmetric vertical directivity, unusual for a tower speaker. Distortion is incredibly low even down to 30Hz at 86dB SPL/1m, and stays low even at 96dB and 102dB SPL/1m - the reviewer found essentially no audible tonality change across that whole output range. Watch for: A dip around 1-1.2kHz on-axis is attributed to a diffraction effect, and shows up as a smaller dip in the predicted in-room response. Horizontal beamwidth of about ±40 degrees is on the narrower side, though the transition from wide to constant directivity is smooth. Minimum impedance dips to 3.2 ohms around 580Hz, calling for an amplifier comfortable with a demanding load. 4-ohm nominal impedance overall.
What the Dynaudio Emit 30 offers: A 2.5-way floorstander: two 5.25” mid-woofers paired with a roughly 1” dome tweeter, driven through dual rear bass-reflex ports. The two woofers hand off at staggered crossover points (around 1kHz and 3.5kHz) rather than sharing one, which avoids the acoustic lobing a shared crossover point would cause between the tweeter and the lower woofer, and adds a few dB of sensitivity in the process. Genuinely deep bass for a speaker around this price - measured F3 near 44Hz and extends audibly down to about 40Hz in-room without much difficulty. Harmonic distortion measures clean and low at both 86dB and 96dB SPL/1m. Good CTA-2034 sound power and uniform directivity mean the speaker takes EQ correction well if a listener wants to dial in its one tonal weak point. Dynamic range and compression performance are strong overall, with only a minor, high-Q compression artifact tied to a cone-edge resonance that’s unlikely to be audible. Wide, consistent horizontal dispersion around ±70° with just a small ~10° narrowing between 1-3kHz, and a reasonably forgiving ±20° vertical window centered on the tweeter axis. Watch for: A dip and inconsistency in the lower-treble presence region (roughly 2-5kHz) makes the top end sound uneven - sometimes soft, sometimes forward - depending on the specific instrument or frequency being reproduced; male vocals can lack presence and cymbals can lack sizzle as a result. A cone-edge surround resonance shows up around 1-1.3kHz in burst-decay measurements (a trait the reviewer has also seen on other Dynaudio models) and lines up with elevated multitone distortion across roughly 600Hz-1.5kHz. An enclosure resonance appears around 350Hz in the impedance curve. Placed too close to a rear wall, the dual ports make the bass noticeably boomy - pulling the speaker out is needed to keep the low end from overloading the room. Fully resolving the top-end inconsistency needs a modest EQ correction (roughly +2dB with a Q of about 1, centered 3-6kHz), so out-of-the-box tonal accuracy in that band isn’t quite class-leading despite otherwise strong measured performance.
Buy the KEF R11 Meta if sound quality matters more than the price. Buy the Dynaudio Emit 30 if the price matters more than sound quality.
If sound quality matters at all to you, skip the Dynaudio Emit 30. It ranks near the bottom of the 68 floorstanding speakers, so look higher up the list instead.
Specifications Side By Side
| KEF R11 Meta | Dynaudio Emit 30 | |
|---|---|---|
| Price | $3,499.99 | $1,274.25 |
| Ranked | #26 of 68 in Large Size Floorstanding Speakers | #53 of 68 in Large Size Floorstanding Speakers |
| Bass Extension (-10dB) | 31Hz (measured, Audio Science Review) | 36Hz (measured, Erin’s Audio Corner) |
| Bass Extension (-3dB) | 64Hz (measured, Audio Science Review) | 44Hz (measured, Erin’s Audio Corner) |
| Dimensions | 51"H x 12.2"W x 15.1"D (1295.4 x 309.9 x 383.5 mm) | 35.4"H x 6.7"W x 10.7"D (900.0 x 170.0 x 272.0 mm) |
| Impedance | 4 ohms | 4 ohms |
| Drivers | 4 x 165 mm (6.5 in.) hybrid aluminium cone woofers, 125 mm (5 in.) aluminium cone midrange, 25 mm (1 in.) vented aluminium dome with MAT tweeter | Dual 5.25" mid-woofers, 1" soft dome tweeter |
| Sensitivity | 89.5dB | 87dB |
| Weight | 80.5 lbs / 36.5 kg each | 34.2 lbs / 15.5 kg |
| Woofer Cabinet | ported, rear | ported, rear (dual) |
| Frequency Response | - | 44Hz - 25kHz (±3dB, manufacturer specified) |
| Power Handling | - | 180W (IEC rated) |
| Country of Origin | - | Denmark |
Related Speaker Comparisons
More useful head-to-heads from the same speaker class:
- Klipsch Heresy IV vs Klipsch RP-6000F II
- Arendal 1961 Tower vs PSB Imagine T65
- Klipsch Heresy IV vs Klipsch RP-8000F II
- KEF R11 Meta vs KEF Q11 Meta
- KEF R11 Meta vs Magnepan LRS+
Prices on this page were last checked August 24, 2026 at 6:53 AM UTC. Product prices and availability are accurate as of that date/time and are subject to change; the price and availability shown on Amazon at the time of purchase will apply to the purchase of this product.
As an eBay Partner, we may be compensated if you make a purchase.
The Two Speakers In Full
KEF R11 Meta: $3,499.99 Amazon eBay
Pros: CEA2034 spinorama shows a generally flat on-axis response with good directivity and very deep bass extension (F10 of 30Hz). Predicted in-room response is very smooth aside from the small 1-1.5kHz dip. The coaxial Uni-Q driver gives excellent, symmetric vertical directivity, unusual for a tower speaker. Distortion is incredibly low even down to 30Hz at 86dB SPL/1m, and stays low even at 96dB and 102dB SPL/1m - the reviewer found essentially no audible tonality change across that whole output range.
Cons: A dip around 1-1.2kHz on-axis is attributed to a diffraction effect, and shows up as a smaller dip in the predicted in-room response. Horizontal beamwidth of about ±40 degrees is on the narrower side, though the transition from wide to constant directivity is smooth. Minimum impedance dips to 3.2 ohms around 580Hz, calling for an amplifier comfortable with a demanding load. 4-ohm nominal impedance overall.
Full KEF R11 Meta review and specifications →
| Bass Extension (-10dB) | 31Hz (measured, Audio Science Review) |
|---|---|
| Bass Extension (-3dB) | 64Hz (measured, Audio Science Review) |
| Dimensions | 51"H x 12.2"W x 15.1"D (1295.4 x 309.9 x 383.5 mm) |
| Drivers | 4 x 165 mm (6.5 in.) hybrid aluminium cone woofers, 125 mm (5 in.) aluminium cone midrange, 25 mm (1 in.) vented aluminium dome with MAT tweeter |
| Impedance | 4 ohms |
| Sensitivity | 89.5dB |
| Weight | 80.5 lbs / 36.5 kg each |
| Woofer Cabinet | ported, rear |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
Dynaudio Emit 30: $1,274.25 Amazon eBay
Pros: A 2.5-way floorstander: two 5.25” mid-woofers paired with a roughly 1” dome tweeter, driven through dual rear bass-reflex ports. The two woofers hand off at staggered crossover points (around 1kHz and 3.5kHz) rather than sharing one, which avoids the acoustic lobing a shared crossover point would cause between the tweeter and the lower woofer, and adds a few dB of sensitivity in the process. Genuinely deep bass for a speaker around this price - measured F3 near 44Hz and extends audibly down to about 40Hz in-room without much difficulty. Harmonic distortion measures clean and low at both 86dB and 96dB SPL/1m. Good CTA-2034 sound power and uniform directivity mean the speaker takes EQ correction well if a listener wants to dial in its one tonal weak point. Dynamic range and compression performance are strong overall, with only a minor, high-Q compression artifact tied to a cone-edge resonance that’s unlikely to be audible. Wide, consistent horizontal dispersion around ±70° with just a small ~10° narrowing between 1-3kHz, and a reasonably forgiving ±20° vertical window centered on the tweeter axis.
Cons: A dip and inconsistency in the lower-treble presence region (roughly 2-5kHz) makes the top end sound uneven - sometimes soft, sometimes forward - depending on the specific instrument or frequency being reproduced; male vocals can lack presence and cymbals can lack sizzle as a result. A cone-edge surround resonance shows up around 1-1.3kHz in burst-decay measurements (a trait the reviewer has also seen on other Dynaudio models) and lines up with elevated multitone distortion across roughly 600Hz-1.5kHz. An enclosure resonance appears around 350Hz in the impedance curve. Placed too close to a rear wall, the dual ports make the bass noticeably boomy - pulling the speaker out is needed to keep the low end from overloading the room. Fully resolving the top-end inconsistency needs a modest EQ correction (roughly +2dB with a Q of about 1, centered 3-6kHz), so out-of-the-box tonal accuracy in that band isn’t quite class-leading despite otherwise strong measured performance.
Full Dynaudio Emit 30 review and specifications →
| Bass Extension (-10dB) | 36Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 44Hz (measured, Erin's Audio Corner) |
| Country of Origin | Denmark |
| Dimensions | 35.4"H x 6.7"W x 10.7"D (900.0 x 170.0 x 272.0 mm) |
| Drivers | Dual 5.25" mid-woofers, 1" soft dome tweeter |
| Frequency Response | 44Hz - 25kHz (±3dB, manufacturer specified) |
| Impedance | 4 ohms |
| Power Handling | 180W (IEC rated) |
| Sensitivity | 87dB |
| Weight | 34.2 lbs / 15.5 kg |
| Woofer Cabinet | ported, rear (dual) |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- Dynaudio Emit 30 vs Klipsch RP-6000F II
- Dynaudio Emit 30 vs Klipsch RP-8000F II
- Dynaudio Emit 30 vs Polk T50
- Dynaudio Emit 30 vs SVS Ultra Evolution Pinnacle
- Dynaudio Emit 30 vs Focal Aria Evo X N°2
- Dynaudio Emit 30 vs Klipsch RP-5000F II
- Dynaudio Emit 30 vs Sony SS-CS3
- Dynaudio Emit 30 vs Infinity Reference 253
- See all 28 comparisons