Short answer: the Mission LX-3 MKII. It ranks #80 of 130 bookshelf speakers by sound quality; the ELAC Debut 2.0 B6.2 ranks #87.
What the ELAC Debut 2.0 B6.2 offers: Reasonably flat on-axis and listening-window response with reasonably even horizontal directivity, holding about ±60° up to roughly 8kHz for consistent stereo width whether aimed directly at the listener or toed out. Its larger-than-typical woofer lets it play very loud with minimal distortion, staying under about 1% THD down to 50Hz at 86dB, and minimum impedance stays a comfortable 5-6 ohms. In-room bass extension reaches about 50Hz without much trouble, enough for a solid kick-drum sound. Takes equalization very well - correcting the on-axis response doesn’t cost sensitivity through the midrange, and the underlying directivity behavior (diffraction, vertical mismatch) is mild enough that EQ alone gets most of the way to a well-balanced sound. Vertical tolerance is asymmetric and fairly forgiving: about 10° above the tweeter axis and 20° below it before tonal balance meaningfully shifts. One reviewer called it “a good speaker” with “a good price” rather than just good-for-the-price, and found it fairly neutral overall in-room. Watch for: A good size resonant peak around 700Hz stands out from an otherwise smooth response and lingers in cumulative spectral decay (waterfall) measurements - in one reviewer’s sighted A/B test, reducing it by about 5dB via EQ made a noticeable but not dramatic difference. Directivity error shows up around 3.3kHz, and the upper-midrange around 4-6kHz stood out as edgy and sharp, almost sibilant at times, in casual listening - the predicted in-room response shows a lack of energy between 1-2kHz and a bit too much above that, which one reviewer thought would sound bright. Distortion at 96dB SPL/1m shows two harmonic peaks the reviewer says “should not be there,” one from woofer breakup around 400Hz and another around 7-8kHz from the tweeter, and multitone distortion approaches 10% in the 500-800Hz range at that output level. Real compression shows up even at moderate volume and worsens at 96dB and above, with the woofer clearly giving up around 60-70Hz - a subwoofer is recommended for anyone wanting to listen loud, since running it full-range at high output costs real dynamic range in the midbass and bass. Don’t place it close to a wall - boundary reinforcement adds a midbass bump that undoes the otherwise smooth, linear response. Getting the best out of it takes EQ (taming the 700Hz peak, filling in the 1-2kHz dip, and trimming the highs).
What the Mission LX-3 MKII offers: A large affordable standmount with a 6.5-inch woofer, 88dB rated sensitivity and useful bass. ASR measured 48Hz estimated in-room extension, a controlled Q of 0.60, a 5.52 subwoofer-assisted preference score and reasonable +/-55-degree horizontal coverage. Watch for: On-axis smoothness of 0.217 and predicted in-room smoothness of 0.344 reveal clear response unevenness, with a -0.46dB-per-octave downward tilt. The 345mm-tall, 8.4kg cabinet is bulky and current US availability is limited.
Buy the ELAC Debut 2.0 B6.2 when the price outweighs sound quality for you, and the Mission LX-3 MKII when sound quality outweighs the price instead.
Looking for alternatives? See the complete Passive Home rankings.
Specifications Side By Side
| ELAC Debut 2.0 B6.2 | Mission LX-3 MKII | |
|---|---|---|
| Price | $329.00 per pair | £249 per pair |
| Ranked | #87 of 130 in Large Size Bookshelf Speakers | #80 of 130 in Large Size Bookshelf Speakers |
| Bass Extension (-10dB) | 40Hz (measured, Erin's Audio Corner) | - |
| Bass Extension (-3dB) | 64Hz (measured, Erin's Audio Corner) | - |
| Impedance | 6 ohms nominal, 5.2 ohms minimum (measured, Erin's Audio Corner) | 8 ohms nominal, 4.1 ohms minimum |
| Sensitivity | 86.5dB (measured, Audio Science Review) | 88dB |
| Drivers | 25mm tweeter + 165mm woofer | 1" microfiber-dome tweeter, 6.5" composite-fiber woofer |
| Weight | 29.1 lbs (13.2 kg) | 18.5 lbs (8.4 kg) each |
| Dimensions | 14.8"H x 7.7"W x 10.6"D (375.0 x 195.0 x 268.0 mm) | 13.6H x 8.9W x 12.1D in |
| Woofer Cabinet | ported, front | - |
| Enclosure | - | 2-way, bass-reflex |
| Country | - | United Kingdom (design) |
| Spinorama Preference Score | - | 3.26 |
| Spinorama Preference Score with Perfect Sub | - | 5.52 |
Related Speaker Comparisons
More top alternatives to Mission LX-3 MKII:
- Perlisten S4b vs Mission LX-3 MKII
- KEF Reference 1 Meta vs Mission LX-3 MKII
- GR-Research NX-Studio vs Mission LX-3 MKII
- AsciLab C6B vs Mission LX-3 MKII
- Audio First Cadentia 3 vs Mission LX-3 MKII
Prices on this page were last checked September 16, 2026 at 12:41 AM UTC. Product prices and availability are accurate as of that date/time and are subject to change; the price and availability shown on Amazon at the time of purchase will apply to the purchase of this product.
As an eBay Partner, we may be compensated if you make a purchase.
The Two Speakers In Full
ELAC Debut 2.0 B6.2: $329.00 per pair Amazon Crutchfield eBay
Pros: Reasonably flat on-axis and listening-window response with reasonably even horizontal directivity, holding about ±60° up to roughly 8kHz for consistent stereo width whether aimed directly at the listener or toed out. Its larger-than-typical woofer lets it play very loud with minimal distortion, staying under about 1% THD down to 50Hz at 86dB, and minimum impedance stays a comfortable 5-6 ohms. In-room bass extension reaches about 50Hz without much trouble, enough for a solid kick-drum sound. Takes equalization very well - correcting the on-axis response doesn’t cost sensitivity through the midrange, and the underlying directivity behavior (diffraction, vertical mismatch) is mild enough that EQ alone gets most of the way to a well-balanced sound. Vertical tolerance is asymmetric and fairly forgiving: about 10° above the tweeter axis and 20° below it before tonal balance meaningfully shifts. One reviewer called it “a good speaker” with “a good price” rather than just good-for-the-price, and found it fairly neutral overall in-room. Measured bass extension of 64Hz (-3dB), with a measured sensitivity of 86.5dB.
Cons: A good size resonant peak around 700Hz stands out from an otherwise smooth response and lingers in cumulative spectral decay (waterfall) measurements - in one reviewer’s sighted A/B test, reducing it by about 5dB via EQ made a noticeable but not dramatic difference. Directivity error shows up around 3.3kHz, and the upper-midrange around 4-6kHz stood out as edgy and sharp, almost sibilant at times, in casual listening - the predicted in-room response shows a lack of energy between 1-2kHz and a bit too much above that, which one reviewer thought would sound bright. Distortion at 96dB SPL/1m shows two harmonic peaks the reviewer says “should not be there,” one from woofer breakup around 400Hz and another around 7-8kHz from the tweeter, and multitone distortion approaches 10% in the 500-800Hz range at that output level. Real compression shows up even at moderate volume and worsens at 96dB and above, with the woofer clearly giving up around 60-70Hz - a subwoofer is recommended for anyone wanting to listen loud, since running it full-range at high output costs real dynamic range in the midbass and bass. Don’t place it close to a wall - boundary reinforcement adds a midbass bump that undoes the otherwise smooth, linear response. Getting the best out of it takes EQ (taming the 700Hz peak, filling in the 1-2kHz dip, and trimming the highs).
Full ELAC Debut 2.0 B6.2 review and specifications →
| Bass Extension (-10dB) | 40Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 64Hz (measured, Erin's Audio Corner) |
| Dimensions | 14.8"H x 7.7"W x 10.6"D (375.0 x 195.0 x 268.0 mm) |
| Drivers | 25mm tweeter + 165mm woofer |
| Impedance | 6 ohms nominal, 5.2 ohms minimum (measured, Erin's Audio Corner) |
| Sensitivity | 86.5dB (measured, Audio Science Review) |
| Weight | 29.1 lbs (13.2 kg) |
| Woofer Cabinet | ported, front |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- ELAC Debut 2.0 B6.2 vs SVS Prime Bookshelf
- ELAC Debut 2.0 B6.2 vs Dynaudio Special Forty
- ELAC Debut 2.0 B6.2 vs KEF Q3 Meta
- ELAC Debut 2.0 B6.2 vs Polk Monitor XT20
- ELAC Debut 2.0 B6.2 vs Infinity IL10
- ELAC Debut 2.0 B6.2 vs GR-Research X-LS Encore
- ELAC Debut 2.0 B6.2 vs Sonus Faber Lumina II
- ELAC Debut 2.0 B6.2 vs XTZ Spirit 4
- See all 59 comparisons
Mission LX-3 MKII: £249 per pair Richer Sounds eBay
Pros: A large affordable standmount with a 6.5-inch woofer, 88dB rated sensitivity and useful bass. ASR measured 48Hz estimated in-room extension, a controlled Q of 0.60, a 5.52 subwoofer-assisted preference score and reasonable +/-55-degree horizontal coverage.
Cons: On-axis smoothness of 0.217 and predicted in-room smoothness of 0.344 reveal clear response unevenness, with a -0.46dB-per-octave downward tilt. The 345mm-tall, 8.4kg cabinet is bulky and current US availability is limited.
Full Mission LX-3 MKII review and specifications →
| Country | United Kingdom (design) |
|---|---|
| Dimensions | 13.6H x 8.9W x 12.1D in |
| Drivers | 1" microfiber-dome tweeter, 6.5" composite-fiber woofer |
| Enclosure | 2-way, bass-reflex |
| Impedance | 8 ohms nominal, 4.1 ohms minimum |
| Sensitivity | 88dB |
| Spinorama Preference Score | 3.26 |
| Spinorama Preference Score with Perfect Sub | 5.52 |
| Weight | 18.5 lbs (8.4 kg) each |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- Mission LX-3 MKII vs GR-Research X-LS Encore
- Mission LX-3 MKII vs Philharmonic BMR Monitor
- Mission LX-3 MKII vs Dynaudio Emit 20
- Mission LX-3 MKII vs Klipsch RP-600M II
- Mission LX-3 MKII vs Dynaudio Special Forty
- Mission LX-3 MKII vs SVS Prime Bookshelf
- Mission LX-3 MKII vs KEF Q3 Meta
- Mission LX-3 MKII vs Polk Signature Elite ES20
- See all 44 comparisons