Short answer: the ELAC Debut 3.0 DB63. It ranks #41 of 125 bookshelf speakers by sound quality at $499; the Sonus Faber Sonetto II G2 ranks #99 and costs $3500, so there is not much of a tradeoff to weigh.
What the ELAC Debut 3.0 DB63 offers: 1” aluminum dome tweeter with a distinctive partial-lens waveguide design paired with a 6.5” third-generation aramid fiber cone woofer, in a robustly built cabinet for the price. Shallow bass rolloff (F3 76Hz, F10 40Hz) allows placement close to a wall without excessive boominess, useful for smaller living rooms. Solid measured performance for the price: on-axis linearity within about 2.5dB, impedance dipping only to about 4.4 ohms (easily AVR-driven), and roughly 20-26dB of usable dynamic range. A clear improvement over its sibling ELAC DB62, which has a sibilance issue tied to the crossover that can’t be fixed with EQ. Wide horizontal radiation of about ±60°, giving a spacious soundstage. Distortion looks good at a moderate 86dB and still reasonable at 96dB. Takes well to EQ correction - the reviewer provides a specific filter set (a low-shelf boost at 650Hz plus peaking cuts/boosts at 550Hz, 660Hz, and 3kHz) that meaningfully smooths out its known deviations. Watch for: A dip in the lower midrange (300-600Hz, about 1.5dB) reduces vocal warmth and can make voices sound slightly hollow. A high-Q resonance around 650-750Hz shows up clearly in measurements, though the reviewer couldn’t reliably hear it in his own A/B testing. A dip around 2-3kHz (roughly 1-2dB) slightly reduces speech intelligibility and attack in the upper midrange. Directivity droops above about 2kHz as the midwoofer narrows toward its beaming frequency while the tweeter’s pattern behaves differently - an inherent trade-off of physically separated drivers that can’t be fully corrected without introducing other issues. Multitone distortion crosses the reviewer’s 3% threshold in the 200Hz-1kHz range, and adding a subwoofer at an 80Hz crossover only modestly reduces it. Toeing the speaker away from the listener loses noticeable top-end air and cymbal energy, giving a softer upper register. Practical loudness ceiling is around 90dB at typical listening distance before midrange distortion and bass attack begin to degrade. Still needs a subwoofer for extension below about 40Hz.
What the Sonus Faber Sonetto II G2 offers: Two-way design with a 1.125” damped Apex Dome silk tweeter and 6.5” cone woofer, using a base of concrete, aluminum, and steel with under-cabinet venting. Notably more neutral than Sonus Faber’s own Lumina 2, which runs 2-5dB hotter in the treble. Horizontal directivity narrows at a fairly constant, well-behaved rate rather than narrowing-then-widening-then-narrowing like some rivals (including the Lumina 2), meaning sidewall reflections match the direct sound well enough that the reviewer doesn’t recommend sidewall absorption for this speaker. The tweeter-to-woofer crossover handoff around 3kHz looks clean, suggesting a higher-order crossover than typical for the size/price class. Good dynamic range - the low end loses only about 2dB from 76dB to 96dB, otherwise holding up well. Not a difficult amplifier load (about 4.2 ohms minimum impedance). Bass extension reaches a genuine 50Hz in-room, fuller than the Lumina 2. Watch for: Sounds notably bright pointed directly on-axis; toeing the speaker out about 30° reduces treble energy and sibilance meaningfully. A resonance around 700Hz gives vocals a slightly nasal, hollow quality. A dip in the upper midrange (roughly 1-2kHz) reduces perceived detail and attack, while the elevated treble can read as “analytical” or “detailed” to some listeners despite being a coloration rather than true resolution. Needs more clearance from the rear wall than some rivals - about 1.5-2 feet in an ideal room, more or less depending on your specific room modes - or the 80-120Hz region can become boomy. Vertical listening window is limited to about ±10-15° from the tweeter axis. Some unexplained directivity irregularities appear around 1.2kHz and 1.6kHz, possibly port-related, along with a longer decay in the 800Hz-1600Hz range in burst-decay measurements. Multitone distortion approaches the reviewer’s 3% threshold through the midrange, though likely not obviously audible without direct A/B comparison. A resonance in the cabinet appears around 400Hz in impedance measurements.
Buy the ELAC Debut 3.0 DB63. It ranks higher for sound quality than the Sonus Faber Sonetto II G2 and costs less, so there is no real case for the other one.
If sound quality matters at all to you, skip the Sonus Faber Sonetto II G2. It ranks near the bottom of the 125 bookshelf speakers, so look higher up the list instead.
Specifications Side By Side
| ELAC Debut 3.0 DB63 | Sonus Faber Sonetto II G2 | |
|---|---|---|
| Price | $499.00 | $3500 |
| Ranked | #41 of 125 in Large Size Bookshelf Speakers | #99 of 125 in Large Size Bookshelf Speakers |
| Bass Extension (-10dB) | 40Hz (measured, Erin’s Audio Corner) | 38Hz (measured, Erin’s Audio Corner) |
| Bass Extension (-3dB) | 76Hz (measured, Erin’s Audio Corner) | 62Hz (measured, Erin’s Audio Corner) |
| Dimensions | 13.3"H x 7.7"W x 11.7"D (337.8 x 195.6 x 297.2 mm) | 16.3"H x 8.9"W x 14"D (414.3 x 227.0 x 355.6 mm) |
| Impedance | 6 ohms nominal (4.4 ohms minimum, measured, Erin’s Audio Corner) | 4 ohms nominal (4.2 ohms minimum, measured by Erin’s Audio Corner) |
| Sensitivity | 86.2dB (measured, Erin’s Audio Corner) | 87dB (measured, Erin’s Audio Corner) |
| Drivers | 6.5" Aramid Fiber woofer, 1" soft dome tweeter | 1x 6.5" mid-woofer (paper cone), 1x 1.1" (28mm) DAD soft dome tweeter |
| Weight | 17.2 lbs / 7.8 kg each | 38.4 lbs / 17.4 kg |
| Woofer Cabinet | ported, rear | ported, front |
Related Speaker Comparisons
More useful head-to-heads from the same speaker class:
- Philharmonic BMR (v1) vs Arendal 1723 Bookshelf S THX
- Pylon Jasper Monitor 18 vs Sonus Faber Lumina II Amator
- Arendal 1723 Bookshelf S THX vs JBL HDI-1600
- ELAC Debut 3.0 DB63 vs MoFi SourcePoint 10
- Klipsch RP-600M II vs Sonus Faber Sonetto II G2
Prices on this page were last checked August 24, 2026 at 6:53 AM UTC. Product prices and availability are accurate as of that date/time and are subject to change; the price and availability shown on Amazon at the time of purchase will apply to the purchase of this product.
As an eBay Partner, we may be compensated if you make a purchase.
The Two Speakers In Full
ELAC Debut 3.0 DB63: $499.00 Amazon Crutchfield eBay
Pros: 1” aluminum dome tweeter with a distinctive partial-lens waveguide design paired with a 6.5” third-generation aramid fiber cone woofer, in a robustly built cabinet for the price. Shallow bass rolloff (F3 76Hz, F10 40Hz) allows placement close to a wall without excessive boominess, useful for smaller living rooms. Solid measured performance for the price: on-axis linearity within about 2.5dB, impedance dipping only to about 4.4 ohms (easily AVR-driven), and roughly 20-26dB of usable dynamic range. A clear improvement over its sibling ELAC DB62, which has a sibilance issue tied to the crossover that can’t be fixed with EQ. Wide horizontal radiation of about ±60°, giving a spacious soundstage. Distortion looks good at a moderate 86dB and still reasonable at 96dB. Takes well to EQ correction - the reviewer provides a specific filter set (a low-shelf boost at 650Hz plus peaking cuts/boosts at 550Hz, 660Hz, and 3kHz) that meaningfully smooths out its known deviations.
Cons: A dip in the lower midrange (300-600Hz, about 1.5dB) reduces vocal warmth and can make voices sound slightly hollow. A high-Q resonance around 650-750Hz shows up clearly in measurements, though the reviewer couldn’t reliably hear it in his own A/B testing. A dip around 2-3kHz (roughly 1-2dB) slightly reduces speech intelligibility and attack in the upper midrange. Directivity droops above about 2kHz as the midwoofer narrows toward its beaming frequency while the tweeter’s pattern behaves differently - an inherent trade-off of physically separated drivers that can’t be fully corrected without introducing other issues. Multitone distortion crosses the reviewer’s 3% threshold in the 200Hz-1kHz range, and adding a subwoofer at an 80Hz crossover only modestly reduces it. Toeing the speaker away from the listener loses noticeable top-end air and cymbal energy, giving a softer upper register. Practical loudness ceiling is around 90dB at typical listening distance before midrange distortion and bass attack begin to degrade. Still needs a subwoofer for extension below about 40Hz.
Full ELAC Debut 3.0 DB63 review and specifications →
| Bass Extension (-10dB) | 40Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 76Hz (measured, Erin's Audio Corner) |
| Dimensions | 13.3"H x 7.7"W x 11.7"D (337.8 x 195.6 x 297.2 mm) |
| Drivers | 6.5" Aramid Fiber woofer, 1" soft dome tweeter |
| Impedance | 6 ohms nominal (4.4 ohms minimum, measured, Erin's Audio Corner) |
| Sensitivity | 86.2dB (measured, Erin's Audio Corner) |
| Weight | 17.2 lbs / 7.8 kg each |
| Woofer Cabinet | ported, rear |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- ELAC Debut 3.0 DB63 vs Emotiva Airmotiv XB2
- ELAC Debut 3.0 DB63 vs JBL HDI-1600
- ELAC Debut 3.0 DB63 vs Revel Concerta2 M16
- ELAC Debut 3.0 DB63 vs ELAC VELA BS 403
- ELAC Debut 3.0 DB63 vs Revel M126Be
- ELAC Debut 3.0 DB63 vs Wharfedale Linton 85
- ELAC Debut 3.0 DB63 vs ELAC Uni-Fi Reference UBR62
- ELAC Debut 3.0 DB63 vs Dynaudio Heritage Special
- See all 52 comparisons
Sonus Faber Sonetto II G2: $3500 Crutchfield eBay
Pros: Two-way design with a 1.125” damped Apex Dome silk tweeter and 6.5” cone woofer, using a base of concrete, aluminum, and steel with under-cabinet venting. Notably more neutral than Sonus Faber’s own Lumina 2, which runs 2-5dB hotter in the treble. Horizontal directivity narrows at a fairly constant, well-behaved rate rather than narrowing-then-widening-then-narrowing like some rivals (including the Lumina 2), meaning sidewall reflections match the direct sound well enough that the reviewer doesn’t recommend sidewall absorption for this speaker. The tweeter-to-woofer crossover handoff around 3kHz looks clean, suggesting a higher-order crossover than typical for the size/price class. Good dynamic range - the low end loses only about 2dB from 76dB to 96dB, otherwise holding up well. Not a difficult amplifier load (about 4.2 ohms minimum impedance). Bass extension reaches a genuine 50Hz in-room, fuller than the Lumina 2.
Cons: Sounds notably bright pointed directly on-axis; toeing the speaker out about 30° reduces treble energy and sibilance meaningfully. A resonance around 700Hz gives vocals a slightly nasal, hollow quality. A dip in the upper midrange (roughly 1-2kHz) reduces perceived detail and attack, while the elevated treble can read as “analytical” or “detailed” to some listeners despite being a coloration rather than true resolution. Needs more clearance from the rear wall than some rivals - about 1.5-2 feet in an ideal room, more or less depending on your specific room modes - or the 80-120Hz region can become boomy. Vertical listening window is limited to about ±10-15° from the tweeter axis. Some unexplained directivity irregularities appear around 1.2kHz and 1.6kHz, possibly port-related, along with a longer decay in the 800Hz-1600Hz range in burst-decay measurements. Multitone distortion approaches the reviewer’s 3% threshold through the midrange, though likely not obviously audible without direct A/B comparison. A resonance in the cabinet appears around 400Hz in impedance measurements.
Full Sonus Faber Sonetto II G2 review and specifications →
| Bass Extension (-10dB) | 38Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 62Hz (measured, Erin's Audio Corner) |
| Dimensions | 16.3"H x 8.9"W x 14"D (414.3 x 227.0 x 355.6 mm) |
| Drivers | 1x 6.5" mid-woofer (paper cone), 1x 1.1" (28mm) DAD soft dome tweeter |
| Impedance | 4 ohms nominal (4.2 ohms minimum, measured by Erin's Audio Corner) |
| Sensitivity | 87dB (measured, Erin's Audio Corner) |
| Weight | 38.4 lbs / 17.4 kg |
| Woofer Cabinet | ported, front |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- Sonus Faber Sonetto II G2 vs Audio Craftsmen Victoria
- Sonus Faber Sonetto II G2 vs Pylon Jasper Monitor 18
- Sonus Faber Sonetto II G2 vs KEF Q350
- Sonus Faber Sonetto II G2 vs Emotiva Airmotiv B2+
- Sonus Faber Sonetto II G2 vs Sonus Faber Lumina II Amator
- Sonus Faber Sonetto II G2 vs JBL XPL-90
- Sonus Faber Sonetto II G2 vs Polk Reserve R100
- Sonus Faber Sonetto II G2 vs Klipsch RP-600M
- See all 29 comparisons