Short answer: the ELAC Debut 3.0 DB63 for better sound quality, the Klipsch RP-600M for the lower price. The ELAC Debut 3.0 DB63 ranks #41 of 122 bookshelf speakers at $499. The Klipsch RP-600M ranks #100 at $343.22, $155.78 cheaper.
What the ELAC Debut 3.0 DB63 offers: 1” aluminum dome tweeter with a distinctive partial-lens waveguide design paired with a 6.5” third-generation aramid fiber cone woofer, in a robustly built cabinet for the price. Shallow bass rolloff (F3 76Hz, F10 40Hz) allows placement close to a wall without excessive boominess, useful for smaller living rooms. Solid measured performance for the price: on-axis linearity within about 2.5dB, impedance dipping only to about 4.4 ohms (easily AVR-driven), and roughly 20-26dB of usable dynamic range. A clear improvement over its sibling ELAC DB62, which has a sibilance issue tied to the crossover that can’t be fixed with EQ. Wide horizontal radiation of about ±60°, giving a spacious soundstage. Distortion looks good at a moderate 86dB and still reasonable at 96dB. Takes well to EQ correction - the reviewer provides a specific filter set (a low-shelf boost at 650Hz plus peaking cuts/boosts at 550Hz, 660Hz, and 3kHz) that meaningfully smooths out its known deviations. Watch for: A dip in the lower midrange (300-600Hz, about 1.5dB) reduces vocal warmth and can make voices sound slightly hollow. A high-Q resonance around 650-750Hz shows up clearly in measurements, though the reviewer couldn’t reliably hear it in his own A/B testing. A dip around 2-3kHz (roughly 1-2dB) slightly reduces speech intelligibility and attack in the upper midrange. Directivity droops above about 2kHz as the midwoofer narrows toward its beaming frequency while the tweeter’s pattern behaves differently - an inherent trade-off of physically separated drivers that can’t be fully corrected without introducing other issues. Multitone distortion crosses the reviewer’s 3% threshold in the 200Hz-1kHz range, and adding a subwoofer at an 80Hz crossover only modestly reduces it. Toeing the speaker away from the listener loses noticeable top-end air and cymbal energy, giving a softer upper register. Practical loudness ceiling is around 90dB at typical listening distance before midrange distortion and bass attack begin to degrade. Still needs a subwoofer for extension below about 40Hz.
What the Klipsch RP-600M offers: More linear horizontal dispersion than the updated RP-600M II - as you move side-to-side, the tonal character changes less, a genuine advantage for off-axis listening consistency. Takes exceptionally well to EQ correction (miniDSP or similar), letting a knowledgeable owner fix its tonal shortcomings without needing to upgrade. Standard 6.5” woofer/horn-tweeter two-way design with reasonably gradual bass rolloff (F3 ~70Hz, F10 ~40Hz) rather than a steep vented-enclosure cutoff. Watch for: A strong, annoying resonance in the lower vocal range around 300Hz stands out clearly (though it can be EQ’d out). Overall tonal balance is notably less neutral than the newer RP-600M II, with a roughly 3-4dB suckout in the estimated in-room response. The waveguide doesn’t extend flush to the baffle edge, increasing diffraction compared to the redesigned version. Klipsch’s marketed sensitivity spec (about 96dB) is a half-space, in-room-style rating roughly 9dB above the true anechoic figure (closer to 85-86dB), which can mislead buyers comparing spec sheets. Elevated treble on-axis, similar to its successor, benefits from toe-out or careful placement. Vertical listening tolerance is limited to about ±10° from the tweeter axis. Still needs a subwoofer for real bass weight; a boost around 120Hz gives kick drums their “tambour” without the underlying “meat.”
Buy the ELAC Debut 3.0 DB63 if sound quality matters more than the price. Buy the Klipsch RP-600M if the price matters more than sound quality.
If sound quality matters at all to you, skip the Klipsch RP-600M. It ranks near the bottom of the 122 bookshelf speakers, so look higher up the list instead.
Specifications Side By Side
| ELAC Debut 3.0 DB63 | Klipsch RP-600M | |
|---|---|---|
| Price | $499.00 | $343.22 Discontinued |
| Ranked | #41 of 122 in Large Size Bookshelf Speakers | #100 of 122 in Large Size Bookshelf Speakers |
| Bass Extension (-10dB) | 40Hz (measured, Erin’s Audio Corner) | 40Hz (measured, Erin’s Audio Corner) |
| Bass Extension (-3dB) | 76Hz (measured, Erin’s Audio Corner) | 73Hz (measured, Erin’s Audio Corner) |
| Dimensions | 13.3"H x 7.7"W x 11.7"D (337.8 x 195.6 x 297.2 mm) | 15.7"H x 8"W x 11.9"D (398.8 x 203.2 x 302.3 mm) |
| Impedance | 6 ohms nominal (4.4 ohms minimum, measured, Erin’s Audio Corner) | 8 ohms nominal, 3.5 ohms minimum (measured, Erin’s Audio Corner) |
| Sensitivity | 86.2dB (measured, Erin’s Audio Corner) | 85.2dB (measured, Erin’s Audio Corner) |
| Drivers | 6.5" Aramid Fiber woofer, 1" soft dome tweeter | 6.5" Cerametallic cone woofer, 1" titanium LTS vented tweeter with Tractrix horn |
| Weight | 17.2 lbs / 7.8 kg each | 16.1 lbs / 7.3 kg each |
| Woofer Cabinet | ported, rear | ported |
| Discontinued | - | Yes |
Related Speaker Comparisons
More useful head-to-heads from the same speaker class:
- Emotiva Airmotiv XB2 vs Monolith Encore C6
- Emotiva Airmotiv B2+ vs Wharfedale Diamond 9.1
- Emotiva Airmotiv XB2 vs Monolith Encore B6
- Klipsch RP-600M vs Yamaha NS-10
- ELAC Debut 3.0 DB63 vs HiVi Swans 3.1A Sehlin Sound Solutions mod
Prices on this page were last checked August 24, 2026 at 6:53 AM UTC. Product prices and availability are accurate as of that date/time and are subject to change; the price and availability shown on Amazon at the time of purchase will apply to the purchase of this product.
As an eBay Partner, we may be compensated if you make a purchase.
The Two Speakers In Full
ELAC Debut 3.0 DB63: $499.00 Amazon Crutchfield eBay
Pros: 1” aluminum dome tweeter with a distinctive partial-lens waveguide design paired with a 6.5” third-generation aramid fiber cone woofer, in a robustly built cabinet for the price. Shallow bass rolloff (F3 76Hz, F10 40Hz) allows placement close to a wall without excessive boominess, useful for smaller living rooms. Solid measured performance for the price: on-axis linearity within about 2.5dB, impedance dipping only to about 4.4 ohms (easily AVR-driven), and roughly 20-26dB of usable dynamic range. A clear improvement over its sibling ELAC DB62, which has a sibilance issue tied to the crossover that can’t be fixed with EQ. Wide horizontal radiation of about ±60°, giving a spacious soundstage. Distortion looks good at a moderate 86dB and still reasonable at 96dB. Takes well to EQ correction - the reviewer provides a specific filter set (a low-shelf boost at 650Hz plus peaking cuts/boosts at 550Hz, 660Hz, and 3kHz) that meaningfully smooths out its known deviations.
Cons: A dip in the lower midrange (300-600Hz, about 1.5dB) reduces vocal warmth and can make voices sound slightly hollow. A high-Q resonance around 650-750Hz shows up clearly in measurements, though the reviewer couldn’t reliably hear it in his own A/B testing. A dip around 2-3kHz (roughly 1-2dB) slightly reduces speech intelligibility and attack in the upper midrange. Directivity droops above about 2kHz as the midwoofer narrows toward its beaming frequency while the tweeter’s pattern behaves differently - an inherent trade-off of physically separated drivers that can’t be fully corrected without introducing other issues. Multitone distortion crosses the reviewer’s 3% threshold in the 200Hz-1kHz range, and adding a subwoofer at an 80Hz crossover only modestly reduces it. Toeing the speaker away from the listener loses noticeable top-end air and cymbal energy, giving a softer upper register. Practical loudness ceiling is around 90dB at typical listening distance before midrange distortion and bass attack begin to degrade. Still needs a subwoofer for extension below about 40Hz.
Full ELAC Debut 3.0 DB63 review and specifications →
| Bass Extension (-10dB) | 40Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 76Hz (measured, Erin's Audio Corner) |
| Dimensions | 13.3"H x 7.7"W x 11.7"D (337.8 x 195.6 x 297.2 mm) |
| Drivers | 6.5" Aramid Fiber woofer, 1" soft dome tweeter |
| Impedance | 6 ohms nominal (4.4 ohms minimum, measured, Erin's Audio Corner) |
| Sensitivity | 86.2dB (measured, Erin's Audio Corner) |
| Weight | 17.2 lbs / 7.8 kg each |
| Woofer Cabinet | ported, rear |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- ELAC Debut 3.0 DB63 vs Emotiva Airmotiv XB2
- ELAC Debut 3.0 DB63 vs JBL HDI-1600
- ELAC Debut 3.0 DB63 vs Revel Concerta2 M16
- ELAC Debut 3.0 DB63 vs ELAC VELA BS 403
- ELAC Debut 3.0 DB63 vs Revel M126Be
- ELAC Debut 3.0 DB63 vs Wharfedale Linton 85
- ELAC Debut 3.0 DB63 vs ELAC Uni-Fi Reference UBR62
- ELAC Debut 3.0 DB63 vs Dynaudio Heritage Special
- See all 35 comparisons
Klipsch RP-600M: $343.22 Discontinued Amazon eBay
Pros: More linear horizontal dispersion than the updated RP-600M II - as you move side-to-side, the tonal character changes less, a genuine advantage for off-axis listening consistency. Takes exceptionally well to EQ correction (miniDSP or similar), letting a knowledgeable owner fix its tonal shortcomings without needing to upgrade. Standard 6.5” woofer/horn-tweeter two-way design with reasonably gradual bass rolloff (F3 ~70Hz, F10 ~40Hz) rather than a steep vented-enclosure cutoff.
Cons: A strong, annoying resonance in the lower vocal range around 300Hz stands out clearly (though it can be EQ’d out). Overall tonal balance is notably less neutral than the newer RP-600M II, with a roughly 3-4dB suckout in the estimated in-room response. The waveguide doesn’t extend flush to the baffle edge, increasing diffraction compared to the redesigned version. Klipsch’s marketed sensitivity spec (about 96dB) is a half-space, in-room-style rating roughly 9dB above the true anechoic figure (closer to 85-86dB), which can mislead buyers comparing spec sheets. Elevated treble on-axis, similar to its successor, benefits from toe-out or careful placement. Vertical listening tolerance is limited to about ±10° from the tweeter axis. Still needs a subwoofer for real bass weight; a boost around 120Hz gives kick drums their “tambour” without the underlying “meat.”. Discontinued.
Full Klipsch RP-600M review and specifications →
| Bass Extension (-10dB) | 40Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 73Hz (measured, Erin's Audio Corner) |
| Dimensions | 15.7"H x 8"W x 11.9"D (398.8 x 203.2 x 302.3 mm) |
| Discontinued | Yes |
| Drivers | 6.5" Cerametallic cone woofer, 1" titanium LTS vented tweeter with Tractrix horn |
| Impedance | 8 ohms nominal, 3.5 ohms minimum (measured, Erin's Audio Corner) |
| Sensitivity | 85.2dB (measured, Erin's Audio Corner) |
| Weight | 16.1 lbs / 7.3 kg each |
| Woofer Cabinet | ported |
- Links
- Reviews, Comparisons and Sound Samples
- Erin’s Audio Corner: The Truth about Klipsch’s “NEW” Sound. RP-600M Update. More from Erin’s Audio Corner →
- Erin’s Audio Corner Website Klipsch RP-600M
- GR-Research: We Bought The “NEW” RP-600M II Is KLIPSCH Listening?! More from GR-Research →
- Audio Science Review Measurements More from Audio Science Review →
- Audio Science Review Measurements (spinorama.org)
- Reddit Search for Klipsch RP-600M Review
- Head-to-Head Comparisons
- Klipsch RP-600M vs Sonus Faber Lumina II Amator
- Klipsch RP-600M vs Wharfedale Diamond 9.1
- Klipsch RP-600M vs Triangle Borea BR03
- Klipsch RP-600M vs KEF Q350
- Klipsch RP-600M vs B&W 805S
- Klipsch RP-600M vs Sonus Faber Sonetto II G2
- Klipsch RP-600M vs Aperion Audio Verus V8B
- Klipsch RP-600M vs Emotiva Airmotiv B2+
- See all 19 comparisons