Short answer: the ELAC Debut 3.0 DB63 for better sound quality, the Behringer B2030P for the lower price. The ELAC Debut 3.0 DB63 ranks #41 of 125 bookshelf speakers at $499. The Behringer B2030P ranks #77 at $220, $279 cheaper.
What the ELAC Debut 3.0 DB63 offers: 1” aluminum dome tweeter with a distinctive partial-lens waveguide design paired with a 6.5” third-generation aramid fiber cone woofer, in a robustly built cabinet for the price. Shallow bass rolloff (F3 76Hz, F10 40Hz) allows placement close to a wall without excessive boominess, useful for smaller living rooms. Solid measured performance for the price: on-axis linearity within about 2.5dB, impedance dipping only to about 4.4 ohms (easily AVR-driven), and roughly 20-26dB of usable dynamic range. A clear improvement over its sibling ELAC DB62, which has a sibilance issue tied to the crossover that can’t be fixed with EQ. Wide horizontal radiation of about ±60°, giving a spacious soundstage. Distortion looks good at a moderate 86dB and still reasonable at 96dB. Takes well to EQ correction - the reviewer provides a specific filter set (a low-shelf boost at 650Hz plus peaking cuts/boosts at 550Hz, 660Hz, and 3kHz) that meaningfully smooths out its known deviations. Watch for: A dip in the lower midrange (300-600Hz, about 1.5dB) reduces vocal warmth and can make voices sound slightly hollow. A high-Q resonance around 650-750Hz shows up clearly in measurements, though the reviewer couldn’t reliably hear it in his own A/B testing. A dip around 2-3kHz (roughly 1-2dB) slightly reduces speech intelligibility and attack in the upper midrange. Directivity droops above about 2kHz as the midwoofer narrows toward its beaming frequency while the tweeter’s pattern behaves differently - an inherent trade-off of physically separated drivers that can’t be fully corrected without introducing other issues. Multitone distortion crosses the reviewer’s 3% threshold in the 200Hz-1kHz range, and adding a subwoofer at an 80Hz crossover only modestly reduces it. Toeing the speaker away from the listener loses noticeable top-end air and cymbal energy, giving a softer upper register. Practical loudness ceiling is around 90dB at typical listening distance before midrange distortion and bass attack begin to degrade. Still needs a subwoofer for extension below about 40Hz.
What the Behringer B2030P offers: CEA2034 spinorama shows strong horizontal directivity control, keeping the response nearly constant off-axis through most of the audible spectrum, with a wide beamwidth that eases seating position and toe-in requirements. Distortion measurements hold up well against the pricier Revel M106 at both 86dB and 106dB SPL. With EQ to tame a resonance around 800Hz and a bit of a bass fill, the reviewer called it a “winner” that could play loud without bottoming out. Watch for: A resonance around 800Hz shows up clearly in the on-axis response and the waterfall/CSD plot, and the flat, near-horizontal predicted in-room response makes it sound bright without an equalization target curve. Vertical directivity is only typical, not exceptional. Long discontinued - the reviewer noted you’ll have to hunt for a used pair.
Buy the ELAC Debut 3.0 DB63 if sound quality matters more than the price. Buy the Behringer B2030P if the price matters more than sound quality.
Specifications Side By Side
| ELAC Debut 3.0 DB63 | Behringer B2030P | |
|---|---|---|
| Price | $499.00 | $220 Discontinued |
| Ranked | #41 of 125 in Large Size Bookshelf Speakers | #77 of 125 in Large Size Bookshelf Speakers |
| Bass Extension (-10dB) | 40Hz (measured, Erin’s Audio Corner) | 60Hz (measured, Audio Science Review) |
| Bass Extension (-3dB) | 76Hz (measured, Erin’s Audio Corner) | 79Hz (measured, Audio Science Review) |
| Dimensions | 13.3"H x 7.7"W x 11.7"D (337.8 x 195.6 x 297.2 mm) | 12.5H x 8.4W x 8.3D in |
| Impedance | 6 ohms nominal (4.4 ohms minimum, measured, Erin’s Audio Corner) | - |
| Sensitivity | 86.2dB (measured, Erin’s Audio Corner) | 84.5dB (2.83V/1m, measured, Audio Science Review) |
| Drivers | 6.5" Aramid Fiber woofer, 1" soft dome tweeter | 6.75" woofer, 0.75" ferrofluid-cooled tweeter |
| Weight | 17.2 lbs / 7.8 kg each | 15.4 lbs / 7.0 kg each |
| Woofer Cabinet | ported, rear | ported, vertical slot |
| Discontinued | - | Yes |
| Frequency Response | - | 75Hz - 21kHz (Manufacturer specified) |
| Power Handling | - | up to 100W |
Related Speaker Comparisons
More useful head-to-heads from the same speaker class:
- Emotiva Airmotiv XB2 vs Monolith Encore C6
- JBL Studio 630 vs Infinity IL10
- Emotiva Airmotiv XB2 vs Monolith Encore B6
- Infinity Reference R162 vs Behringer B2030P
- Klipsch RP-600M II vs Behringer B2030P
Prices on this page were last checked August 24, 2026 at 6:53 AM UTC. Product prices and availability are accurate as of that date/time and are subject to change; the price and availability shown on Amazon at the time of purchase will apply to the purchase of this product.
As an eBay Partner, we may be compensated if you make a purchase.
The Two Speakers In Full
ELAC Debut 3.0 DB63: $499.00 Amazon Crutchfield eBay
Pros: 1” aluminum dome tweeter with a distinctive partial-lens waveguide design paired with a 6.5” third-generation aramid fiber cone woofer, in a robustly built cabinet for the price. Shallow bass rolloff (F3 76Hz, F10 40Hz) allows placement close to a wall without excessive boominess, useful for smaller living rooms. Solid measured performance for the price: on-axis linearity within about 2.5dB, impedance dipping only to about 4.4 ohms (easily AVR-driven), and roughly 20-26dB of usable dynamic range. A clear improvement over its sibling ELAC DB62, which has a sibilance issue tied to the crossover that can’t be fixed with EQ. Wide horizontal radiation of about ±60°, giving a spacious soundstage. Distortion looks good at a moderate 86dB and still reasonable at 96dB. Takes well to EQ correction - the reviewer provides a specific filter set (a low-shelf boost at 650Hz plus peaking cuts/boosts at 550Hz, 660Hz, and 3kHz) that meaningfully smooths out its known deviations.
Cons: A dip in the lower midrange (300-600Hz, about 1.5dB) reduces vocal warmth and can make voices sound slightly hollow. A high-Q resonance around 650-750Hz shows up clearly in measurements, though the reviewer couldn’t reliably hear it in his own A/B testing. A dip around 2-3kHz (roughly 1-2dB) slightly reduces speech intelligibility and attack in the upper midrange. Directivity droops above about 2kHz as the midwoofer narrows toward its beaming frequency while the tweeter’s pattern behaves differently - an inherent trade-off of physically separated drivers that can’t be fully corrected without introducing other issues. Multitone distortion crosses the reviewer’s 3% threshold in the 200Hz-1kHz range, and adding a subwoofer at an 80Hz crossover only modestly reduces it. Toeing the speaker away from the listener loses noticeable top-end air and cymbal energy, giving a softer upper register. Practical loudness ceiling is around 90dB at typical listening distance before midrange distortion and bass attack begin to degrade. Still needs a subwoofer for extension below about 40Hz.
Full ELAC Debut 3.0 DB63 review and specifications →
| Bass Extension (-10dB) | 40Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 76Hz (measured, Erin's Audio Corner) |
| Dimensions | 13.3"H x 7.7"W x 11.7"D (337.8 x 195.6 x 297.2 mm) |
| Drivers | 6.5" Aramid Fiber woofer, 1" soft dome tweeter |
| Impedance | 6 ohms nominal (4.4 ohms minimum, measured, Erin's Audio Corner) |
| Sensitivity | 86.2dB (measured, Erin's Audio Corner) |
| Weight | 17.2 lbs / 7.8 kg each |
| Woofer Cabinet | ported, rear |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- ELAC Debut 3.0 DB63 vs Emotiva Airmotiv XB2
- ELAC Debut 3.0 DB63 vs JBL HDI-1600
- ELAC Debut 3.0 DB63 vs Revel Concerta2 M16
- ELAC Debut 3.0 DB63 vs ELAC VELA BS 403
- ELAC Debut 3.0 DB63 vs Revel M126Be
- ELAC Debut 3.0 DB63 vs Wharfedale Linton 85
- ELAC Debut 3.0 DB63 vs ELAC Uni-Fi Reference UBR62
- ELAC Debut 3.0 DB63 vs Dynaudio Heritage Special
- See all 52 comparisons
Behringer B2030P: $220 Discontinued eBay
Pros: CEA2034 spinorama shows strong horizontal directivity control, keeping the response nearly constant off-axis through most of the audible spectrum, with a wide beamwidth that eases seating position and toe-in requirements. Distortion measurements hold up well against the pricier Revel M106 at both 86dB and 106dB SPL. With EQ to tame a resonance around 800Hz and a bit of a bass fill, the reviewer called it a “winner” that could play loud without bottoming out.
Cons: A resonance around 800Hz shows up clearly in the on-axis response and the waterfall/CSD plot, and the flat, near-horizontal predicted in-room response makes it sound bright without an equalization target curve. Vertical directivity is only typical, not exceptional. Long discontinued - the reviewer noted you’ll have to hunt for a used pair. Discontinued.
Full Behringer B2030P review and specifications →
| Bass Extension (-10dB) | 60Hz (measured, Audio Science Review) |
|---|---|
| Bass Extension (-3dB) | 79Hz (measured, Audio Science Review) |
| Dimensions | 12.5H x 8.4W x 8.3D in |
| Discontinued | Yes |
| Drivers | 6.75" woofer, 0.75" ferrofluid-cooled tweeter |
| Frequency Response | 75Hz - 21kHz (Manufacturer specified) |
| Power Handling | up to 100W |
| Sensitivity | 84.5dB (2.83V/1m, measured, Audio Science Review) |
| Weight | 15.4 lbs / 7.0 kg each |
| Woofer Cabinet | ported, vertical slot |
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- Behringer B2030P vs JBL Studio 630
- Behringer B2030P vs Dynaudio Emit 20
- Behringer B2030P vs Klipsch RP-600M II
- Behringer B2030P vs Infinity IL10
- Behringer B2030P vs Dynaudio Special Forty
- Behringer B2030P vs ELAC Debut 2.0 B6.2
- Behringer B2030P vs SVS Prime Bookshelf
- Behringer B2030P vs KEF Q3 Meta
- See all 10 comparisons