Short answer: the Dynaudio Emit 20. It ranks #75 of 130 bookshelf speakers by sound quality; the Mission LX-3 MKII ranks #80.
What the Dynaudio Emit 20 offers: Two-way design with a 28mm Esotar soft dome tweeter (Hexis-damped) and an 18cm mid-woofer, using a first-order crossover on the tweeter and second-order on the woofer. Exceptional bass extension for a bookshelf speaker - reaches a clean, authoritative 40Hz in-room, rare enough that the reviewer says most listeners could skip a subwoofer for typical music. Very low distortion across the board, staying below 1% THD down to 40Hz at 86dB and below 3% even at 96dB - unusually clean bass performance where most two-way bookshelf speakers start rising in distortion around 80Hz. Wide, remarkably consistent horizontal directivity (about ±50-60°) that holds steady up to roughly 13kHz - rare for a speaker in this format, thanks to a beveled tweeter edge that acts as a mild waveguide. Excellent compression and dynamic-range linearity at the frequency extremes, actually showing slight bass enhancement rather than the sharp low-end compression common in similarly-sized bookshelf speakers. Watch for: A resonance around 600-800Hz gives snares and similar percussion a muffled, flat quality lacking impact - confirmed as originating in the woofer itself (isolated via measurements of the raw driver out of the cabinet), and attempts at constrained-layer damping didn’t resolve it. A peak around 4kHz adds a sharp, edgy quality to some male vocals. A roughly 5dB boost above 10kHz gives cymbals and hi-hats excess shimmer that can sound unnatural, especially pointed directly on-axis. Vertical dispersion shows two separate crossover-related notches (above and below the tweeter reference line around 5kHz) rather than the usual single one, a direct consequence of the shallow crossover slopes used on both drivers. Multitone distortion is elevated in the midrange, possibly due to the woofer’s magnet structure lacking a shorting ring. Best aimed slightly off-axis (about 10-15° of toe-out) to tame the excess high-frequency shimmer, rather than pointed straight at the listener.
What the Mission LX-3 MKII offers: A large affordable standmount with a 6.5-inch woofer, 88dB rated sensitivity and useful bass. ASR measured 48Hz estimated in-room extension, a controlled Q of 0.60, a 5.52 subwoofer-assisted preference score and reasonable +/-55-degree horizontal coverage. Watch for: On-axis smoothness of 0.217 and predicted in-room smoothness of 0.344 reveal clear response unevenness, with a -0.46dB-per-octave downward tilt. The 345mm-tall, 8.4kg cabinet is bulky and current US availability is limited.
Buy the Dynaudio Emit 20 if sound quality is the priority over the price, or the Mission LX-3 MKII if the price is the priority over sound quality.
Looking for alternatives? See the complete Passive Home rankings.
Specifications Side By Side
| Dynaudio Emit 20 | Mission LX-3 MKII | |
|---|---|---|
| Price | $1,049.00 per pair | £249 per pair |
| Ranked | #75 of 130 in Large Size Bookshelf Speakers | #80 of 130 in Large Size Bookshelf Speakers |
| Bass Extension (-10dB) | 33Hz (measured, Erin's Audio Corner) | - |
| Bass Extension (-3dB) | 54Hz (measured, Erin's Audio Corner) | - |
| Drivers | 7.1" Magnesium Silicate Polymer woofer, 1.1" Cerotar soft dome with Hexis tweeter | 1" microfiber-dome tweeter, 6.5" composite-fiber woofer |
| Weight | 12.8 lbs (5.8 kg) | 18.5 lbs (8.4 kg) each |
| Sensitivity | 83.5dB (measured, Erin's Audio Corner; 86dB manufacturer specified) | 88dB |
| Impedance | 6 ohms nominal (5.5 ohms minimum above 80Hz, measured, Erin's Audio Corner) | 8 ohms nominal, 4.1 ohms minimum |
| Dimensions | 14.6"H x 8.1"W x 12.3"D (370.0 x 205.0 x 312.0 mm) | 13.6H x 8.9W x 12.1D in |
| Woofer Cabinet | ported, rear | - |
| Spinorama Preference Score | 3.35 | 3.26 |
| Spinorama Preference Score with Perfect Sub | 5.05 | 5.52 |
| Enclosure | - | 2-way, bass-reflex |
| Country | - | United Kingdom (design) |
Related Speaker Comparisons
More top alternatives to Dynaudio Emit 20:
- Dynaudio Emit 20 vs Perlisten S4b
- KEF Reference 1 Meta vs Dynaudio Emit 20
- Dynaudio Emit 20 vs GR-Research NX-Studio
- Dynaudio Emit 20 vs AsciLab C6B
- Audio First Cadentia 3 vs Dynaudio Emit 20
Prices on this page were last checked September 16, 2026 at 12:41 AM UTC. Product prices and availability are accurate as of that date/time and are subject to change; the price and availability shown on Amazon at the time of purchase will apply to the purchase of this product.
As an eBay Partner, we may be compensated if you make a purchase.
The Two Speakers In Full
Dynaudio Emit 20: $1,049.00 per pair Amazon eBay
Pros: Two-way design with a 28mm Esotar soft dome tweeter (Hexis-damped) and an 18cm mid-woofer, using a first-order crossover on the tweeter and second-order on the woofer. Exceptional bass extension for a bookshelf speaker - reaches a clean, authoritative 40Hz in-room, rare enough that the reviewer says most listeners could skip a subwoofer for typical music. Very low distortion across the board, staying below 1% THD down to 40Hz at 86dB and below 3% even at 96dB - unusually clean bass performance where most two-way bookshelf speakers start rising in distortion around 80Hz. Wide, remarkably consistent horizontal directivity (about ±50-60°) that holds steady up to roughly 13kHz - rare for a speaker in this format, thanks to a beveled tweeter edge that acts as a mild waveguide. Excellent compression and dynamic-range linearity at the frequency extremes, actually showing slight bass enhancement rather than the sharp low-end compression common in similarly-sized bookshelf speakers. Measured bass extension of 54Hz (-3dB), with a measured sensitivity of 83.5dB.
Cons: A resonance around 600-800Hz gives snares and similar percussion a muffled, flat quality lacking impact - confirmed as originating in the woofer itself (isolated via measurements of the raw driver out of the cabinet), and attempts at constrained-layer damping didn’t resolve it. A peak around 4kHz adds a sharp, edgy quality to some male vocals. A roughly 5dB boost above 10kHz gives cymbals and hi-hats excess shimmer that can sound unnatural, especially pointed directly on-axis. Vertical dispersion shows two separate crossover-related notches (above and below the tweeter reference line around 5kHz) rather than the usual single one, a direct consequence of the shallow crossover slopes used on both drivers. Multitone distortion is elevated in the midrange, possibly due to the woofer’s magnet structure lacking a shorting ring. Best aimed slightly off-axis (about 10-15° of toe-out) to tame the excess high-frequency shimmer, rather than pointed straight at the listener.
Full Dynaudio Emit 20 review and specifications →
| Bass Extension (-10dB) | 33Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 54Hz (measured, Erin's Audio Corner) |
| Dimensions | 14.6"H x 8.1"W x 12.3"D (370.0 x 205.0 x 312.0 mm) |
| Drivers | 7.1" Magnesium Silicate Polymer woofer, 1.1" Cerotar soft dome with Hexis tweeter |
| Impedance | 6 ohms nominal (5.5 ohms minimum above 80Hz, measured, Erin's Audio Corner) |
| Sensitivity | 83.5dB (measured, Erin's Audio Corner; 86dB manufacturer specified) |
| Spinorama Preference Score | 3.35 |
| Spinorama Preference Score with Perfect Sub | 5.05 |
| Weight | 12.8 lbs (5.8 kg) |
| Woofer Cabinet | ported, rear |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- Dynaudio Emit 20 vs Klipsch RP-600M II
- Dynaudio Emit 20 vs Philharmonic BMR Monitor
- Dynaudio Emit 20 vs JBL Studio 630
- Dynaudio Emit 20 vs Behringer B2030P
- Dynaudio Emit 20 vs Polk Signature Elite ES20
- Dynaudio Emit 20 vs GR-Research X-LS Encore
- Dynaudio Emit 20 vs Infinity IL10
- Dynaudio Emit 20 vs Ascend CBM-170 SE2
- See all 63 comparisons
Mission LX-3 MKII: £249 per pair Richer Sounds eBay
Pros: A large affordable standmount with a 6.5-inch woofer, 88dB rated sensitivity and useful bass. ASR measured 48Hz estimated in-room extension, a controlled Q of 0.60, a 5.52 subwoofer-assisted preference score and reasonable +/-55-degree horizontal coverage.
Cons: On-axis smoothness of 0.217 and predicted in-room smoothness of 0.344 reveal clear response unevenness, with a -0.46dB-per-octave downward tilt. The 345mm-tall, 8.4kg cabinet is bulky and current US availability is limited.
Full Mission LX-3 MKII review and specifications →
| Country | United Kingdom (design) |
|---|---|
| Dimensions | 13.6H x 8.9W x 12.1D in |
| Drivers | 1" microfiber-dome tweeter, 6.5" composite-fiber woofer |
| Enclosure | 2-way, bass-reflex |
| Impedance | 8 ohms nominal, 4.1 ohms minimum |
| Sensitivity | 88dB |
| Spinorama Preference Score | 3.26 |
| Spinorama Preference Score with Perfect Sub | 5.52 |
| Weight | 18.5 lbs (8.4 kg) each |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- Mission LX-3 MKII vs GR-Research X-LS Encore
- Mission LX-3 MKII vs Philharmonic BMR Monitor
- Mission LX-3 MKII vs Klipsch RP-600M II
- Mission LX-3 MKII vs Dynaudio Special Forty
- Mission LX-3 MKII vs ELAC Debut 2.0 B6.2
- Mission LX-3 MKII vs SVS Prime Bookshelf
- Mission LX-3 MKII vs KEF Q3 Meta
- Mission LX-3 MKII vs Polk Signature Elite ES20
- See all 44 comparisons