Short answer: the Wharfedale Super Linton. It ranks #24 of 130 bookshelf speakers by sound quality at $2699; the Radiant Acoustics Clarity 6.2 ranks #27 and costs $4500, so there is not much of a tradeoff to weigh.
What the Wharfedale Super Linton offers: Three-way design with a 1” soft dome tweeter, 5” woven Kevlar mid-range, and 8” woven Kevlar woofer in a dual rear-ported, heavily damped MDF/particle-board cabinet. Comes as a genuinely matched pair (measured within about 1dB of each other) and includes custom matching stands. A major dynamic-range improvement over the original Heritage Linton - kick drums retain their impact from low to high volume instead of compressing, the standout objective improvement in this update. Fixes the original Linton’s main flaw: a 1-3kHz scoop that made it sound a bit soft and subdued is filled in here, giving noticeably more attack and dynamic punch. About 3dB more sensitivity than the original Linton (measured ~88.2dB), meaning roughly half the amplifier power for the same output. Wide horizontal radiation of about ±70°, right in the reviewer’s preferred range for an enveloping soundstage. Lower midrange distortion than the original Linton. Bass-shelf tuning intentionally allows closer-to-wall placement (about 1 foot worked well) without excess boominess, more flexible than the original Linton in that regard. Watch for: Rolls off earlier than the original Linton (F3 77Hz versus the original’s 52Hz), a deliberate trade-off for the closer-wall-placement flexibility. On-axis, there’s a mild treble lift around 4-6kHz that can sound a touch sibilant, though the reviewer found it not very noteworthy in practice. Diffraction shows up around 1.5-2kHz on-axis; needs about 10° of toe-out to smooth this out, though going further to 30° starts to lose some top-end air. Distortion peaks slightly higher than the original Linton in the 50-70Hz region. Minimum impedance dips to about 3 ohms around 150Hz, so a 4-ohm-stable amplifier is recommended for best results. Vertical dispersion of about ±20° means multi-row home theater seating outside that window will hear reduced top-end. Asymmetrical design requires attention to setup (tweeters need to face outward) for the most linear in-room response. A costly upgrade for existing Linton owners if the original’s specific flaws didn’t bother them.
What the Radiant Acoustics Clarity 6.2 offers: Custom AMT (Air Motion Transformer) tweeter paired with a 6.5” Purifi Eikona midrange and dual Purifi passive radiators in a passive-radiator enclosure, crossed over at 2.4kHz. Rigid cabinet construction (21mm MDF with a 15mm aluminum front baffle, extensive internal bracing) helps keep resonance in check. A deliberately rising on-axis response paired with narrowing directivity above about 2kHz yields a genuinely linear, non-fatiguing in-room sound rather than the “fake detail” of speakers with a straight treble boost. Excellent pair matching between units (within about 1dB), contributing to precise, well-focused imaging that clearly separated fine details in test tracks. In-room bass extension reaches a solid 40Hz with real kick-drum authority, not just sub-bass rumble. Class-leading dynamic range and compression performance - among the best the reviewer has measured at this price point. Watch for: Needs a fairly specific setup to sound its best: about 15-20° of toe-out (per the manufacturer’s own recommendation) and roughly 2 feet from the rear wall; pointed straight on-axis, the treble reads as noticeably elevated. Low impedance (2.1-ohm minimum, about 1-ohm minimum EPDR) demands an amplifier genuinely comfortable with 4-ohm-and-below loads. Soundstage width narrows above about 5kHz, even though the AMT tweeter itself is capable of wider dispersion. An unexplained resonance appears in harmonic distortion measurements on both units tested (though not on the reviewer’s reference speaker) - possibly a basket resonance, and not something the reviewer could hear. A minor bump around 500Hz in the estimated in-room response could add a touch of boxiness for some listeners, though the reviewer didn’t personally notice it. F3 of 55Hz and F10 of 32Hz mean a subwoofer is still needed for home-theater rumble or bass-heavy genres like rap.
Buy the Wharfedale Super Linton. It ranks higher for sound quality than the Radiant Acoustics Clarity 6.2 and costs less, so the other one has nothing left to offer.
Want more options? Browse the full Passive Home rankings.
Specifications Side By Side
| Wharfedale Super Linton | Radiant Acoustics Clarity 6.2 | |
|---|---|---|
| Price | $2,699.00 per pair | $4500 per pair |
| Ranked | #24 of 130 in Large Size Bookshelf Speakers | #27 of 130 in Large Size Bookshelf Speakers |
| Bass Extension (-10dB) | 34Hz (measured, Erin's Audio Corner) | 32Hz (measured, Erin's Audio Corner) |
| Bass Extension (-3dB) | 77Hz (measured, Erin's Audio Corner) | 55Hz (measured, Erin's Audio Corner) |
| Dimensions | 23.8"H x 11.8"W x 13"D (604.5 x 299.7 x 330.2 mm) | 14.3"H x 8.7"W x 10.5"D (363.2 x 221 x 266.7 mm) |
| Impedance | 4 ohms nominal (3 ohms minimum, measured, Erin's Audio Corner) | 4 ohms nominal (2.1 ohms minimum above 80Hz, measured, Erin's Audio Corner) |
| Drivers | 8"(200mm) black woven Kevlar® cone woofer, 5"(135mm) black woven Kevlar® cone midrange, 1" (25mm) soft dome tweeter | 6.5" PURIFI USHINDI woofer, Custom AMT (Air Motion Transformer) tweeter |
| Sensitivity | 88.2dB (measured, Erin's Audio Corner) | 84.3dB (measured, Erin's Audio Corner) |
| Weight | 43.7 lbs (19.8 kg) each | 23.8 lbs (10.8 kg) each |
| Woofer Cabinet | ported, rear | passive radiator |
| Spinorama Preference Score | 5.28 | 5.13 |
| Spinorama Preference Score with Perfect Sub | 7.12 | 6.90 |
Related Speaker Comparisons
More worthwhile head-to-heads for Wharfedale Super Linton:
- Wharfedale Super Linton vs Perlisten S4b
- Wharfedale Super Linton vs KEF Reference 1 Meta
- Wharfedale Super Linton vs GR-Research NX-Studio
- Wharfedale Super Linton vs AsciLab C6B
- Wharfedale Super Linton vs Audio First Cadentia 3
Prices on this page were last checked September 16, 2026 at 12:41 AM UTC. Product prices and availability are accurate as of that date/time and are subject to change; the price and availability shown on Amazon at the time of purchase will apply to the purchase of this product.
As an eBay Partner, we may be compensated if you make a purchase.
The Two Speakers In Full
Wharfedale Super Linton: $2,699.00 per pair Amazon Crutchfield eBay
Pros: Three-way design with a 1” soft dome tweeter, 5” woven Kevlar mid-range, and 8” woven Kevlar woofer in a dual rear-ported, heavily damped MDF/particle-board cabinet. Comes as a genuinely matched pair (measured within about 1dB of each other) and includes custom matching stands. A major dynamic-range improvement over the original Heritage Linton - kick drums retain their impact from low to high volume instead of compressing, the standout objective improvement in this update. Fixes the original Linton’s main flaw: a 1-3kHz scoop that made it sound a bit soft and subdued is filled in here, giving noticeably more attack and dynamic punch. About 3dB more sensitivity than the original Linton (measured ~88.2dB), meaning roughly half the amplifier power for the same output. Wide horizontal radiation of about ±70°, right in the reviewer’s preferred range for an enveloping soundstage. Lower midrange distortion than the original Linton. Bass-shelf tuning intentionally allows closer-to-wall placement (about 1 foot worked well) without excess boominess, more flexible than the original Linton in that regard. Measured bass extension of 77Hz (-3dB), with a measured sensitivity of 88.2dB.
Cons: Rolls off earlier than the original Linton (F3 77Hz versus the original’s 52Hz), a deliberate trade-off for the closer-wall-placement flexibility. On-axis, there’s a mild treble lift around 4-6kHz that can sound a touch sibilant, though the reviewer found it not very noteworthy in practice. Diffraction shows up around 1.5-2kHz on-axis; needs about 10° of toe-out to smooth this out, though going further to 30° starts to lose some top-end air. Distortion peaks slightly higher than the original Linton in the 50-70Hz region. Minimum impedance dips to about 3 ohms around 150Hz, so a 4-ohm-stable amplifier is recommended for best results. Vertical dispersion of about ±20° means multi-row home theater seating outside that window will hear reduced top-end. Asymmetrical design requires attention to setup (tweeters need to face outward) for the most linear in-room response. A costly upgrade for existing Linton owners if the original’s specific flaws didn’t bother them.
Full Wharfedale Super Linton review and specifications →
| Bass Extension (-10dB) | 34Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 77Hz (measured, Erin's Audio Corner) |
| Dimensions | 23.8"H x 11.8"W x 13"D (604.5 x 299.7 x 330.2 mm) |
| Drivers | 8"(200mm) black woven Kevlar® cone woofer, 5"(135mm) black woven Kevlar® cone midrange, 1" (25mm) soft dome tweeter |
| Impedance | 4 ohms nominal (3 ohms minimum, measured, Erin's Audio Corner) |
| Sensitivity | 88.2dB (measured, Erin's Audio Corner) |
| Spinorama Preference Score | 5.28 |
| Spinorama Preference Score with Perfect Sub | 7.12 |
| Weight | 43.7 lbs (19.8 kg) each |
| Woofer Cabinet | ported, rear |
- Links
- Reviews, Comparisons and Sound Samples
- Erin’s Audio Corner: 5 Reasons Wharfedale Super Linton is the Hidden Gem of Audio Equipment More from Erin’s Audio Corner →
- Erin’s Audio Corner Website Wharfedale Super Linton Review
- Erin’s Audio Corner: Upgrade Your Sound with These 6 Surprisingly Affordable Speakers!
- Erin’s Audio Corner: My Absolute Favorite Products of 2024 Revealed
- Erin’s Audio Corner Measurements (spinorama.org)
- Head-to-Head Comparisons
- Wharfedale Super Linton vs Ascend Acoustics CMT-340 SE2
- Wharfedale Super Linton vs Arendal 1528 Monitor 8
- Wharfedale Super Linton vs MoFi SourcePoint 10
- Wharfedale Super Linton vs Dynaudio Heritage Special
- Wharfedale Super Linton vs AsciLab F6Bs
- Wharfedale Super Linton vs MoFi SourcePoint 8
- Wharfedale Super Linton vs Wharfedale Linton 85
- Wharfedale Super Linton vs Buchardt Audio E50
- See all 51 comparisons
Radiant Acoustics Clarity 6.2: $4500 per pair Radiantacoustics eBay
Pros: Custom AMT (Air Motion Transformer) tweeter paired with a 6.5” Purifi Eikona midrange and dual Purifi passive radiators in a passive-radiator enclosure, crossed over at 2.4kHz. Rigid cabinet construction (21mm MDF with a 15mm aluminum front baffle, extensive internal bracing) helps keep resonance in check. A deliberately rising on-axis response paired with narrowing directivity above about 2kHz yields a genuinely linear, non-fatiguing in-room sound rather than the “fake detail” of speakers with a straight treble boost. Excellent pair matching between units (within about 1dB), contributing to precise, well-focused imaging that clearly separated fine details in test tracks. In-room bass extension reaches a solid 40Hz with real kick-drum authority, not just sub-bass rumble. Class-leading dynamic range and compression performance - among the best the reviewer has measured at this price point. Measured bass extension of 55Hz (-3dB), with a measured sensitivity of 84.3dB.
Cons: Needs a fairly specific setup to sound its best: about 15-20° of toe-out (per the manufacturer’s own recommendation) and roughly 2 feet from the rear wall; pointed straight on-axis, the treble reads as noticeably elevated. Low impedance (2.1-ohm minimum, about 1-ohm minimum EPDR) demands an amplifier genuinely comfortable with 4-ohm-and-below loads. Soundstage width narrows above about 5kHz, even though the AMT tweeter itself is capable of wider dispersion. An unexplained resonance appears in harmonic distortion measurements on both units tested (though not on the reviewer’s reference speaker) - possibly a basket resonance, and not something the reviewer could hear. A minor bump around 500Hz in the estimated in-room response could add a touch of boxiness for some listeners, though the reviewer didn’t personally notice it. F3 of 55Hz and F10 of 32Hz mean a subwoofer is still needed for home-theater rumble or bass-heavy genres like rap.
Full Radiant Acoustics Clarity 6.2 review and specifications →
| Bass Extension (-10dB) | 32Hz (measured, Erin's Audio Corner) |
|---|---|
| Bass Extension (-3dB) | 55Hz (measured, Erin's Audio Corner) |
| Dimensions | 14.3"H x 8.7"W x 10.5"D (363.2 x 221 x 266.7 mm) |
| Drivers | 6.5" PURIFI USHINDI woofer, Custom AMT (Air Motion Transformer) tweeter |
| Impedance | 4 ohms nominal (2.1 ohms minimum above 80Hz, measured, Erin's Audio Corner) |
| Sensitivity | 84.3dB (measured, Erin's Audio Corner) |
| Spinorama Preference Score | 5.13 |
| Spinorama Preference Score with Perfect Sub | 6.90 |
| Weight | 23.8 lbs (10.8 kg) each |
| Woofer Cabinet | passive radiator |
- Links
- Reviews, Comparisons and Sound Samples
- Head-to-Head Comparisons
- Radiant Acoustics Clarity 6.2 vs MoFi SourcePoint 10
- Radiant Acoustics Clarity 6.2 vs Dynaudio Heritage Special
- Radiant Acoustics Clarity 6.2 vs Ascend Acoustics CMT-340 SE2
- Radiant Acoustics Clarity 6.2 vs Wharfedale Linton 85
- Radiant Acoustics Clarity 6.2 vs Arendal 1528 Monitor 8
- Radiant Acoustics Clarity 6.2 vs Ascend Acoustics Sierra-LX
- Radiant Acoustics Clarity 6.2 vs Revel M126Be
- Radiant Acoustics Clarity 6.2 vs AsciLab F6Bs
- See all 45 comparisons